Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
I'm trying to read data over UART as fast as possible using the double-buffering feature and EasyDMA, but even this simple example I've posted is losing data.
I've set up...
The wake on GPIO is working all the time now.
Unfortunately, I want to disable it except when needed.
Here is the scenario:
Power up, pushbutton pin senses clicks...
I am using the nrf52832 and according to the errata v1.1 the same contains a problem in the spi, according to clause 3.13 the engineering versions (QFAA-AA0, QFAA-AC0) and...
Hey..
I'm having difficulties using P1 pins for UARTE0 and/or UARTE1.
configuring the RX & TX pins like this works great:
#define RBP_UARTE0_RX_PIN_NUMBER NRF_GPIO_PIN_MAP...
Hi,
I'm using a NRF52832. I'm looking to measure the battery voltage. I'm using 2XAAA cells in serie (voltage range between 2V and 3V).
Below is the configuration to...
Sometimes, when I want to use the nrfjprog tool, I get the following error:
nrfjprog --log -f nrf52 --reset
ERROR: JLinkARM DLL reported an error. Try again. If error...
I cannot start Power Profiler Kit software. I followed the installing instructions, but ended up with the following:
>python.exe ppk.py
Traceback (most recent call last...
I'm developing for the NRF52 DK (nRF52832) using VisualGDB (which uses SDK v11.0.0).
Right now I'm facing two problems:
1. How do I properly handle interrupts while using...
There are tickets from 3 years ago that claim that nested CRITICAL_REGION_ENTER calls are not supported. Or they are supported if you write your own macros.
It appears to...
Hi there,
When using a PIN as RESET, what is the minimum activation time required to insure a reset?
I thought this should feature in Table 16.10.3 but I could not figure...
What is the logger message pool? There are two main definitions for it:
NRF_LOG_MSGPOOL_ELEMENT_COUNT
NRF_LOG_MSGPOOL_ELEMENT_SIZE
However it is not clear what it...
Hello ,
I want to use the NVIC to manage the interruption of the accelerometer and to run a specific program, are you ideas about the possibility of this?
Best Regard...
hi,
I am using nrf 52 DK and softdevice S132,PCA10040 board . I need to toggle a pin,set a pin,reset a pin .can anyone take this ticket to a sample code/ code snippet and...
