Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I followed the instructions and comments in devzone.nordicsemi.com/.../ . I built a project around the ble_app_gls example (with a couple of minor changes such as using -DNRF_LOG_USES_RTT...
Hi, I would like to program nRF51822 flash over SWD interface. I have another micro LPC1100 series that has the flash image for RF51822 and connected to nRF51822 over SWDIO...
Hi,
It is written in the nf_drv_uart.h file for nrf_drv_uart_rx_abort() that
If Easy DMA is not used event will be
called from the function context. If
Easy DMA...
Dear All,
We work on the NRF52 CSP revB. We have a board with two external crystals (32MhZ and 32kHz).
When we use the example program with BLE and UART, it works great...
Hi,
How can i get time stamp from RTC1 timer? While i am using app_timer + Softdevice?
Or any other way
Thanks and Regards,just to get timestamps from timer?
Faizan...
Hi,
I added DFU function to the example of ble_app_hids_keyboard according to ble_app_hrs_dfu.uvproj.
Test environment: nrf51822_xxAA, SDK_v6_1_0 and S110_v7_1, before...
Hi all,
I would like to use Pstorage module. Since flash endurance is 20.000 write/erase cycle, I need to use it very efficiently. If I use pstorage_update function it...
Hello,
I am quite new to Beacon development. I am trying to use the examples of NRF SDK 10.0 on the NRF Beacon. I would like to "install" the application via OTA. I tried...
Hello,
DFU tool (android) is cool but if you have a lot of devices to update it's long. Is there any batch tool that can update all devices that fit (MAC list or SSID filter...
When executing the Bond command on the 8001 and trying to pair it from my laptop (Windows 10) or iPhone (iOS 9), I receive a strange order of events to the command:
...
I'm trying to replicate an Arduino Uno application where we connect a M3Q alcohol sensor into an analog pin and feed the data into the ADC. The specific board I have is made...
Hello,
sd_softdevice_enable falls in hardfault. I have no 32.768 KHz crystal but is set lfclk with NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM.
I'm running my application on a...
