HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party repository within the SDK itself...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hello,
I'm trying to implement a DFU support into the application, and in order to learn how it works, I'm following the steps at the page developer.nordicsemi.com/......
Is there an easy way to find out the range of handles for a service which I added? Obviously the first one is the service handle, then you add characteristics and descriptors...
Hi,
While access sd_ble_gattc_write api, I got an error code 0x00000011. If I check nordic document for sd_ble_gattc_write error code, I can't find any error code with...
I would like to use nRF2460 in my project (Hearing Aid for elder people).In that I need to transmit the data from a mic/line in to >30 receivers within a range of 100 yards...
I'm using nRF51822 and i want to send a notification to the central to notify it for the changing of a characteristic value (major_value) after using the sd_ble_gatts_value_set...
I currently have a custom service emulating the batterey service. I have added an extra characteristic to recieve data from the central in the same way as ble_app_uart. the...
Like explained in this tutorial , on master control panel I do File-> Flash Programming and reprogram the dongle, which then turns on one more LED on the dongle. But, I still...
I'm using SDK 7.1, PCA10028 eval board, SD110, MCP 3.8.0.7
I've compiled and loaded the dfu_dual_bank_ble_s110 project into my PCA100028 board. It shows up in the MCP as...
Hey,
I use ESB protocol on nrf51822. I am using one Pipe currently I can achieve only 183 Kbps, I read that i can achieve 1Mbps data rate if we use ESB. I have few questions...
I understand that it is possible to set a static passkey on the nRF51822.
However, what I would like to do is handle the verification of the user-entered passkey myself...
Hello all,
I am completely new to BLE and would like to make a sensor network with nRF51822 ( 1x S120 as center node and 8x S110 as slaves) I have been reading the content...
I am trying to make my NRF 51 advertise forever till someone connects. I have based myself on the ble_uart example where it uses fast advertising with 40 ms intervals for...
Hi,
Last year, I heard that nordic semi will release a SoftDevice for central that supports mulitple packets per interval time until June, 2015.
For now, I guess s120...
My understanding so far is that the input buffer of GPIO is disconnected by default and we can keep it disconnected for saving power when the pin is configured as output....
Hello,
I just read this paper "High speed data streaming with nRF24L01 " where we can achieve 1.6 Mbps Data Rate in clean RF environment. I am currently using nrf51822 in...
