Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit(nrf52832)
2、what is my purpose?
the quality of thingy52 audio demo is not good(iphone7)...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
Hi all,
I'm working with the reception of 802.15.4 packets on nRF52840 for which I have configure the radio as follows:
In the application loop we have:
...
Hi,
I am using nRF52 SDK v16 and I am wondering where one can find relevant information regarding peripheral event handlers.
Here are a few puzzles I have for now:
...
the central(phone) connected my board,when i call sd_ble_gap_disconnect ,sometimes,not every,return err_code =0x00000008,and not firing BLE_GAP_EVT_DISCONNECTED,also not advertising...
Hello All:
I am working on the time service of NRF52. As I know, there are two standard profiles refer to the time service, one is CTS(Current Time Service) and the other...
Hi All,
I am doing a BLE Mesh development project with nRF52840. SDK version: nRF5 SDK v15.3.0 & nRF5 SDK for Mesh v3.2.0
Case 1:
- IDE: Keil
- Example tested: nRF5...
Hi,
Im working on a configuration where role switching is neccessary.
The following is expected:
- all nodes will be advertising when "idle"
- nodes only need to...
Hi,
When the ble_stack_init(); is called the eeprom flash read/write/erash gets hanged.
But when commented ble_stack_init(); the eeprom flash read/write/erash works...
I recently got a Thingy:91 and activated it. Now I am installing the tools to work with it in my system (Linux) following the nrf Connect v3.3.0 Getting Started Assistant...
Good day. Can I get SES free licenses for multiple devices while evaluating a single development kit or the free license can only be requested for a single divice?
Hi, I use the nFR52832 chip to design as the MCU of my prodcution, it has 8 scan whitelist for user. But I want more number of whitelist for my prodcution. So ,Could you tell...
I have set up the NCS toolchain, followed the instructions to update the JLink DLL in SES, and successfully built/flashed a few examples to the app core (ie. debug/ppi_trace...
I would like to send TCP message with 50KB message size. I saw that maximum size was limited by CONFIG_HEAP_MEM_POOL_SIZE which was 16kB.
Is there any way to send that message...
Hi,
we are experiencing unexpected behavior during sleep entry. Following pictures were taken using an oscilloscope, our device sends a radio transmission every 150 ms...