Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hey,
I am getting a
warning: #47-D: incompatible redefinition of macro "STATIC_ASSERT_SIMPLE" (declared at line 215) warning: #47-D: incompatible redefinition of macro...
Hello, I am working on a ble application which is streaming data via ble notifications. I am currently queuing up the packets in the notification queue and keeping track of...
Hello,
I am trying to use as least energy as possible. I run the ble_app_blinky example. The only change I did was commenting out: advertising_start(); such that no advertising...
Hello,
I'm using the nRF52840 Development Kit and SDK16.0.0_98a08e2.
I'm trying to run the example "proprietary_rf\esb_ptx\pca10056\".
It compiles and runs if I do not...
Hi,
I am not getting the exact starting and ending address of user flash storage like other controllers, How we can find that while using FDS and Fstorage and also i want...
I have a custom board with 5 buttons, and a status LED, using the nrf52832_xxaa chip. 2 of the 5 buttons never trigger an interrupt. It seems like this is because nrf_gpio_pin_read...
Hello, Nordic.
I'm currently developing multiple sensor beacons and a scanner for asset tracking (scanner app based on ble_app_uart_c)
ble_app_uart_c has SCAN...
Hello,
Im designing a board with nRF52832 with acceleration sensor and BLE application, so for the esd protection, should there be an housing of some sort, what all can...
We're migrating from Zentri AMS002 chip to to nRF52840.
We use custom service UUID: "175f8f23-a570-49bd-9627-815a6a27de2a" in nRF firmware.
As attached images show, custom...
Hi!
We're developing a board where we would like to switch between normal power mode (VDD shorted with VDDH) and high power mode (VDDH as input and VDD in highZ or supplying...
Hello everyone. I'm looking for BT5.1 most supported at current moment chip - to have devboard and SDK with ability of direction finding. Which one you can recommend? As I...
We are working with nRF52, in that we want to select any fix channel of BLE. We does not want to use ADH mechanism due to form a whole network on one channel.
So can you...
this is the log I'm getting but it is not clear for me why is the build failing
Building ?spm/zephyr/include/generated/driver-validation.h? from solution ?build? in configuration...
