Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello Nordic Community,
I made custom hardware using nRF9160. I updated modem with latest firmware version 1.1.0.
After updating at_client example code my log file as...
Purchased nRF9160 DK, registered the iBasis SIM card online successfully, but can't connect the cellular network. Checked iBasis's website found the UK is not covered
https...
Hi team,
I was comparing the ble_app_hrs example from SDK v15.3.0 to SDK v16.0.0 and noticed a big difference in the average power consumption. The only change I made to...
I am testing the ble_app_blinky example on nRF52840 BLE SoC and the "nRF Blinky" Android application example which uses the Android-BLE library from NordicSemiconductor. My...
The current implementation of Mesh Config using the flash manager lack a memory listener which can cause it to never retry a store or delete operation.
Assume the following...
Dear Sir,
Could you please recomend board(hardware) that I could move my code that was developed using NRf52 SDK.
I am using ANT functionaluty and s212 software
Best...
Hi Nordic,
I had an initial project with a multilink central connecting to several peripherals through a NUS service, the system is working OK but then I added another connection...
I am using PCA10040 development board for flashing.Same it was working fine to flashing the Custom board.
Now suddenly not flashing to the custom board same board which...
I am planning to use CP2102 (USB to UART) and RF-BM-ND06 NRF52840 bluetooth module for sniffing BLE packets .
Or as an alternative for Nordic Bluetooth USB dongle.
But...
Hello, I'm pretty new to Nordic devices but I have already some experience with other ARM based devices though...
I'm playing with Timers bare metal instructions and figured...
Hi
I am currently trying to get the antenna switching working on the nRF52833 DK. I have an SPDT RF swtich which I want to use for switching between two antennas. I want...
Hi,
I've already asked this problem few days ago, but I couldn't figure out the clear answer.
The above figure shows the VDD values of BLE chip. The power supplied...
0> <debug> nrf_sdh_ble: BLE event: 0x26. 0> <error> app: Fatal error
I started with the nrf_tempelate project and used nrf_uart to add uart service. It works fine but after...
Hi,
I want to know that, can we use this nrf91 for transferring the real time data with tab or mobile phone beyond BLE range. I mean, do we analyse the real time data from...
