Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
I'm having trouble getting the I2C interface working on our nRF54L15-based prototypes. The initial config write to the device fails; specifically, in the twim driver (i2c_nrfx_twim...
Hi There
while extending the actual Sofware with more flash entries i discovered that the capability of provisioing devices decreases, and end up in a hardfault.
Is there...
Hello
In my board I am using an ic as a switch to control the routing of the TX and RX pins of the UART, due to the fact that the nRF9160 does not have more than 4 peripherals...
Hello, I am developing a project that involves authentication over NFC, and need to store a private key in TrustZone. I found the psa_crypto zephyr sample in the sdk, which...
Hi everyone,
I’m trying to understand how wireless mice/keyboards using 2.4 GHz protocols communicate with their receiver dongles so that i can try build one using nRF...
Hi,
I wanted to implement a version of Channel Sounding where you wait for a certain amount of distance estimations, and then try to just select the smallest distance...
Hi, I'm encountering an issue with one particular nRF52832 unit (we use nRF SDK 15.2.0). The problem is that a value 0x20 (decimal 32) is being written to a memory address...
I've been working off this example, which provides a great synchronization mechanism.
https://docs.nordicsemi.com/bundle/ncs-latest/page/nrf/samples/bluetooth/conn_time_sync...
Hi,
I recently wanted to compile this example https://github.com/NordicPlayground/nrf5-ble-tutorial-characteristic?tab=readme-ov-file on another dk to learn about ble development...
Original Title: How to maximize WIFI throughput when using SPI4 between nRF5340 and nRF7002
We are trying to max out the wifi throughput via nRF7002 when connected to...
Hello,
on nrf52811 I want to do advertising once per second. Is it possible using SDK and Zephyr to register an event that advertising was sent - completed? If I understand...
Hello
Is is possible to change the UART pins dynamically? I am thinking to predefine the pins on device tree as follows:
&uart1 {
status = "okay" ;
current-speed...
1. Set up the development environment for the nRF52840 chip in VS Code, but encountered an issue where the chip could not be recognized. The development environment consists...
Hello,
I'm measuring current at the Vbmd jumper for the BMD-350 Eval Board. I'm able to measure 0.9uA running this code:
in the boot immediately after programming...
