Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
What will be the real time effect if we give high value to Tx rather than keeping default Tx value as '0' ? Will it increase signal range?
Regards,
Ashiq Mohammed
I need nRF connect & toolbox on my iphone to do evaluation.
There is nRF toolbox, nRF Beacons but no nRF connet in App store.
Where can I find nRF connect ?
thanks ...
Hi.
Why longer advertising data destroy device ?
When I set length of advertising data to 20bytes in advertising_init(), device will crash and I can't download new firmware...
Hello,
The sd_softdevice_enable returns 8 (captured with my jlink probe), how can I investigate please ?
Configuration:
SDK 15.0.0, SD_132_6.0.0 with bootloader
In my application, I use the peer manager that has called the fds_init function, should I call it again if I want to use the fds to store my data. Will the peer manager use...
Hello Everyone,
I am using Nordic's Power Profiler Kit to estimate the current consumption of an external board. I have been able to configure it properly and getting results...
On nrf52840 I get a current of ~10 uA while sleeping. At the moment I don't run any code and don't start up the softdevice. I go directly to sleep with __WFE(). The result...
Hi All!
Faced with big problem with SCANNING procedure (nRF52840)
We have a BLE network : one CENTRAL and up to 6 PERIPHERALs can be connected simultaneously to the CENTRAL...
I want to detect high to low transitions on 28 GPIO independently. I've read in other posts you can configure 4 pin interrupts or a port interrupt for all pins, but I'm not...
Hello,
I am currently experiencing some problems, when i try using RTT output and the internal clock.
When using an external crystal, everything is working.
The following...
I am working on Ble tutorial of serivces, In step1 they mentioned to declare m_our_service of type ble_os_t. how can I declare that ?I am not sure to consider m_our_service...
Hello
I have been trying to use this repository: https://github.com/NordicPlayground/nrf51-ADC-examples and upon building, i get several errors due to certain header files...
Hi,
I have a Serialization connection working between a Nordic nRF52 CPU (slave) and an NXP CPU (master), using SPI.
The NXP is starting/stopping a BLE Scan on the Nordic...
Hi, I have some questions about the memory map, ram usuage and linker config for the secure bootloader when used with the S332 (4.05 sd_req 0x94) softdevice. I have tried...
USB Virtual COM
Until now, the development has been done by sending the commands via a USB virtual COM. The received buffer of int is processed and sent to the function...
