Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi
Env: keil and no SD
I am doing the first steps on keil + nordic nrf51822. I started by opening the Blinky app (C:\Keil_v5\ARM\PACK\NordicSemiconductor\nRF_Examples...
Hi there ,
i am developing a biomedical recorder which needs to continuously transmit the recorded data ,
data rate is very low (9.6 Kbit/s to 32Kbit/s) but i have a very...
Hello,
I was wondering whether or not there is a way to know, how the connection interval is decided between the two values of the Connection Interval Max and Connection...
Hi, everyone,
We develop the project by using nRF52822 module. But suddnely we discovered that the latest supporting this chip sdk versionis 12.3. The SDK versions newer...
According the the instructions for the Thingy mesh demo, it is possible to manually provision new nodes. Is it possible to identify the unprovisioned node first by sending...
I am trying to make the nrf52832 enter in ON/low power mode for inactivity periode.
I must have the "System ON, No RAM retention, Wake on RTC" as indicated in nrf52832 datasheet...
Hi,
I run the Secure DFU, and I'm doing OTA update without any issue.
The problem is the case that I'm doing an OTA update with a application-version smaller than...
Hi all, Nordic distributors no longer carry the nRF52840-PDK, which included the NFC antenna. What is a direct replacement for the Nordic NFC antenna that used to be included...
I am trying to connect a BerryMed MD1000 Pulse Oximeter (BLE Server) with an Adafruit Bluefruit Feather (nRF52-enabled) Arduino board (BLE Client).
I made an Arduino sketch...
hi All!
I use WAKE UP event from G-SENSOR on some GPIO to wake up the MCU on motion detected.
But sometimes ( ~1% ) the event does not occur for unknown reason until RESET...
Hi,
I want to have 2 SPI slaves on the same bus.
I saw in other posts that in the past it was not supported by the spi driver and that i should use NRF_DRV_SPI_PIN_NOT_USED...
What will be the real time effect if we give high value to Tx rather than keeping default Tx value as '0' ? Will it increase signal range?
Regards,
Ashiq Mohammed
I need nRF connect & toolbox on my iphone to do evaluation.
There is nRF toolbox, nRF Beacons but no nRF connet in App store.
Where can I find nRF connect ?
thanks ...
