Is there a way to recieve more than one write callback for a given characteristic, per radio session? It seems like I can rx 1 time per attribute per radio session and tx...
If it can work with iOS blue setting will be better
I need some reference to dev hid device in IOS
but I can just find my device ,connect ok but not work.
I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
After full update modem firmware and reboot, i got this error:
E: Modem library init error: -116, lte_lc not initialized
The only way to work around is power cycle.Po...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Title
nRF5340 DK × 2 + MCP2515/TJA1050 – can_start() = -5 (CANCTRL/CANSTAT = 0xFF). What am I missing?
Hi everyone,
I’m trying to bring-up a very small CAN bus test...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
Hello!
I have tried in various ways to make the XIP part functional on SDK version 3.0 (SDK v3.0.0-3bfc46578e42) but without success, this on the NRF5340 devkit. I mention...
Hello nordic team!
Context:
Currently I am working on modifying our application code to be able to select, at runtime, which network interface it will use (between ethernet...
Hi,
am working on nrf52840 withst7789v custom display . I have integrated the my display code using lvgl library with PMIC code in zephyr . while doing that I have configure...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
Hi. I used nRF Connect SDK v2.9.1 to add OTA to the Peripheral UART sample application. The target is nRF54L10, but when I build it, the flash usage exceeds 50%.
If the...
Does nRF9160 support IoT devices, SGP.31 eSIM IoT Architecture and Requirements for remote provisioning of eUICCs in Network Constrained and/or User Interface (UI) Constrained...
Hello, we've a nRF9161 DK board a we saw on the back side a footprint for mounting an SD card holder and we found the SD card holder component in the BOM.
Unfortunately...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
I have the following pm_static.yml configuration:
and I'm trying to acces this `custom_bootloader_header` from my application code. Here's the relevant snippet:
...
Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
