Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
nRF52832 / SDK 14.2 / SD5.1.0
There might be two configurations to setup a PPI channel to assign some peripheral event to both timer capture & clear task:
nrf_drv_ppi_channel_assign...
Hello all,
Having a smallish problem seeing printk() output on my board. My board is an NRF9160 PCA10090 inspired board. Long story short, I can't see printk() stuff showing...
My application implements a beacon with services, and a buttonless BLE bootloader.
The application can start the bootloader in two ways.
The first method is executed locally...
Hi,
I am in the process of provisioning and configuring a 2-element light switch server node and a common light switch server. I am using the orginal exemple for the provisioner...
I'm attempting to transfer 256K bps (1 244-byte notification every ~7.5ms) using an nRF52840 using Notifications and am not getting close to the necessary bandwidth. I'm getting...
Hi,
We are developing an application requiring the DFU Service on nRF52832.
The implementation of the DFU Service without bonds works very well, but when switching to...
I've been able to connect to our server using the LTE modem sample app.
As shown below, I configure the modem, open a socket, bind the port, and send and receive a small...
As I'm working on debugging a problem where a TLS connection silently fails with no error code, it occurs to me that it would be VERY handy to have a way to connect wireshark...
In using the Thingy52 I can't figure out how to just get the just XY coordinates from the motion sensor - or any other sensor. I'm trying to figure out if I can capture motion...
hi, i am a student, i am new to nrf52840 DK. I downloaded Gooligmelec "nrf52test-led-battery" from github and open Solution inside SES . it was running ok. when suddenly....
Hello,
I am using nrf52840 and SDK 15.3.0. and the device wakes up every hour and every day for reporting data.
So I am using app timer to wake up also using app_timer...
Hi,
I am working on nrf52840 and using below SDK and softdevice.
SDK - 16.0
Softdevice - S140
IDE - embedded segger studio.
currently using nRF52840-DK.
I am using...
Hi Team,
We are using the Micro ECC functionalities , for that we need the SHA 256 Library,Micro ECC library won't have inbuilt SHA.So how to enable the SHA for Micro...
We are using a nordic 52840 chip with a S140 softdevice as a client to connect with GATT servers from smartphones. When we connect to one of our smartphones, we do get the...
Hi all,
i've try to update the NRF52_DK interface MCU firmware to MBED firmware (nrf5x_atsam3u2c_if_mbed_V0221_11012017.bin).
After power cycle, LD5 at interface MCU...
