HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Using nRF Connect SDK v2.1.0 and the nRF5340 PDK, are any of the ble mesh samples in the fw-nrfconnect-nrf repo working yet? I've tried both the mesh light and light_switch...
Hi community !
I wanted to know if it's possible to program a board as a client and as a server at the same time ?
Cause i want this card to send data into the network...
Using EmbeddedStudio_ARM_Nordic_v452_macos_x64
I am trying to build a sample for 9160-DK
In nRF Connect Options I entered:
Board directory ~/src/ncs/zephyr/boards/arm...
I am attempting to build the latest (4.1.1) pc-ble-driver with 115k2 baudrate. I have a hardware platform which supports 115k2 as maximum baud rate. It seems only the 1m version...
Hi,
I am using the NRF52840 with the usbd_ble_uart example using the latest SDK.nRF5SDK160098a08e2.
My computer (windows 7) recognize the NRF52840 as a nRF52 USB CDC...
Hi. twi_sensor As an example source, I have 2 pressure sensors. I use sdp800 and icp10101 separately and use it as twi_interface to read the sensor value well. However, we...
If I write the data from NrfConnect App and if I again go to the scanner tab without clicking on disconnect or killing the app and then if I click scan or refresh option,...
I want to transfer files to uart using ymodem protcol.
For example, when nRF52840 receives a file through BLE,
it tries to send the file back to the device connected to...
Is there a sure fire way to know for sure that my PSM configuration is correct on the nrf9160DK? I'm trying to get LTE-M + GPS working and I'm still not sure if I'm in PSM...
Hello,
We used the Nrf52810 in our project.
Currently, we found a issue: The ble is disconnected when we press the chip. Because our buttons are on top of the chip. We...
When I use circuit configuration no.5, VDD connected to VDDH and have 5V going into VBUS, I see a 1.6V output from the VDD_nRF (VDD/VDDH).
Normally when I connect a battery...
This question is a follow on to https://devzone.nordicsemi.com/f/nordic-q-a/38085/how-to-create-a-copy-of-examples-project---segger-embedded-studio .
It's clear that making...
Hi,
Can i use nRF52840 Pre Development kit as a sniffer.
Also can i use it to program my customized PCB
Note: I need to do both of above urgently so i cannot wait to...
nrf connect sdk version :1.2.0
application:nrf_: desktop
I use command " west build -b nrf52840_pca20041 -d build_pca20041" , but it report error at last.
I don't know...
Hello
Currently, there are systems that operate with peripherals developed with nRF52832, SDK v.12.2.0. I have a question about supporting this for meshes.
1. Are you...
