Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi everyone,
I am developing a custom PCB that will integrate the nRF52840 SOC. More specifically I will use the MDBT50Q-1MV2 module from Raytac that is approved by Nordic...
I am working on nrf51822 and SDKV10, Softdevice S110. Firmware has implemented whitelist features and enabled bonding.When i bonded the device using nrfConnect App and the...
Hello,
My home application requires standard Wifi 2.4/5Ghz and Bluetooth 5 protocols for communication. I see that nRF has a proprietary Wifi, what are the differences ...
Hi need to change configuration which uart is used when mcuboot is going to serial recovery mode. I would like to have this set for uart1 by adding: Then I put nrf91 in the...
Hi, our product is one set of transmitter/receivier based on nRF24 series. Recently, the number of failures of receivers increases quickly, and most of failures are shown...
Hi community !
I got a weird problem for me. I got a program (BLE Mesh) which i flash on two nRF52840 Dongles, and i got 2 differents behaviour
The first one can be provisioned...
I used nRF connect on iOS to get values from a device. I can see the characteristic property as indicate: when connected it displays the values I need.
1- Is there any way...
HI,
I purchased the nRF51822 Bluetooth Smart Beacon Kit ( I knew it's discontinued ) to perform a quick and simple POC (put my custom 31 bytes for the beacon to advertise...
Hi All.
I have an issue with my development kit. I was working with DFU so I flashed the secure_bootloader project in my nrf52 DK so it is working fine.
But after this...
Hello,
I have an Adafruit Feather M0 Bluefruit LE with an nRF51822 chipset from Nordic and I am currently dealing with Bluetooth Low Energy, especially with profiles, services...
Hi,
As I am new to this BLE applications I am unable to get actual flow of implementing a service to send application specific alert notifications from server which includes...
Hi,
I´m trying to combine the examples "BLE_app_uart" with "TWI_Sensor", because I would like to read data from sensor and put them to my BLE characteristics. I´ve done...
Hi sir
I am getting the current date and time from GPS module . I want to calculate the number of second between 1 Jan 2000 and current date and time. but i am getting how...
Hello, Everyone.
I'm developing a beacon to check the battery level.
I'm current using
nRF51822
SDK11.0.0
Softedevice S130
My inquiry is nRF52 series is...
