in Memfault I see the device ID number for each device such as 41EF6BB8FB6C9AF9. Is the distribution for the first 3 bytes the same as the distribution for the last 3 bytes...
I am using nRF52840 as host processor. Now I need to connect to nRF7002 for WiFi usage. I am using ncs 2.2.2 SDK. I have a few questions? 1. Does nRF7002 work on v2.2.2? I...
Hello, on Memfault when I click on this Developer mode switch, it does nothing. It stays off and doesn't turn on. It does this because I have one device in my project that...
in the datasheet table 80 "GPIO port mapping" the function "CAN-RX" is only listed on P9.4 and P2.8 are these the only two pins it can be assigned to ?
I am struggling to...
Hi All, In the NRF54L15 SoC, the main ARM core and the co-processor RISC core share the same set of peripherals even though both the cores can have separate sections of RAM...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Where can I find documentation for using EasyDMA list mode on SPIM?
I've got nrf51822.
All I can find is this nrf52 documentation , which seems incomplete.
Is there...
I'm new to Gazell, so please excuse the simplicity of my question, but I just seem to be missing something.
I have an application where I will be using one host with two...
Hi
We are about to submit our system for BLE testing. We have been asked for RF-PHY:P9:1 RF-PHY:P9:2 RF-PHY:P10:1 values
RF-PHY:P9:1 Maximum TX packet length (MAX_TX_LENGTH...
Hello Nordic Team,
After setting connection parameters in accordance with Apple BLE design guidelines the BLE throughput has been significantly decreased.
My parameters...
Hello,
If I use the nRF51822 with 128KB ROM and I connect to a external flash via SPI.
The SoftDevice and bootloader are stored in the internal 128K ROM.
Is it possible...
Using GATT characteristic writes to transfer data is slow.Is there a cleaner and/or faster way to do faster OTA upgrade?
Also I wanted to upgrade firmware without affecting...
I have set up a 6lowpan test environment and could control the led3 and led4. could u please provide me with a code to read value at p0.01. i want to connect a temperature...
I directly connect GPIO pin with 24ohm resistor as follows.
And I set GPIO pin as high drive,
NRF_GPIO->PIN_CNF[MY_PIN_NO] |=
(GPIO_PIN_CNF_DRIVE_H0H1 << GPIO_PIN_CNF_DRIVE_Pos...
hello ,i use SDK9.0 ANCS project.when I paired it ,it can work normal. it can recive QQ,wechat,message and so on. but when I paired many times, it will be SystemReset.
...
Hi
I am trying to make an activity tracker with very low power conumption with the nrf52. The Idea is to count interrupts from an accelerometer thtat are generated if the...
Hi
I'm testing Buttonless DFU.
I use SDK 12.2.0 , NRF52 and S132.
I succeeded in entering DFU in Master Control Panel (PC application).
I want to do it even on iOS....
Hello,
I recently finished up the NRF51822 pcb board that I plan on getting printed. I posted my board before and have fixed the problems another user specified.
I used...
Hello,
is it enough to call NVIC_SystemReset() after I flashed a board so that it returns to lower power consumption? Or do I have to pull out the battery?
Marius
