Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
I have been trying for a few days now to get my environment setup for development with the nRF51822. Since there is no official configuration for the Mac w/ Eclipse I have...
Apologies if this has been asked before but did search for 'format' in faq and got nothing.
I have been answering to questions.
In my answer I place hard empty lines....
Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
I am designing Circuit with nRF4122 - QFN package 48 pin, as per datasheet there is circuit for Trace/ PCB Antenna
But i am planning to use Chip Antenna and BAL-NRF02D3...
Hi,
I have a custom board someone designed with two SPI masters and one I2C master. We're now trying to enable the second SPI master and I'm running into errors because...
Hi all,
I am working on FOTA, my set up is with SDK15. I have followed the steps for DFU and i have used the secure_bootloader example, the thing is working fine, i can...
hi i have attached my gps+gsm module with nrf51 development kit and while reading an out put i wont be able to see any output , even with out put i dont know to to do debugging...
Hi,
I have completed all steps in the example at the following link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader and all...
I am developing hardware for the nRF52840. After testing our firmware, we are going to need somewhere around 6,000-7,000 mAh to run our hardware for the time needed. We were...
Hi, all.
I used sd_ble_gap_addr_get() function to get a MAC address in the different example and the result was different.
I tested this example in SDK v14.2 and v15...
Hi,
The amount of information and reference documents available about Bluetooth qualification is overwhelming. It would be great if someone with this experience sheds some...
Do nRF8001 chip has its own internal linear regulator? or Does it need an external like the module created by Adafruit ( https://cdn-learn.adafruit.com/assets/assets/000/035...
Good evening all,
I'm trying to get my DK52 communicating with a CR95HF (this is a NFC controller with serial and SPI control interfaces), I'm using a breakout board - BM019...
Hi Sir, I use load switch circuit to control nrf8001's power. I found even the vcc of nrf8001 is empty, nrf8001 still works. That's not my expected result, I think nrf8001...
Hi ,
We know that the nRF8001 use the random static device address . I have the questions below :
A. Will the device get one new address after power on ? or is the address...
Hi,
I need to exchange data between 2 ble modules.
I'm using SKD 15.0.0 and first ble module is nRF52840, second ble module (esp32) acts as GATT server.
I have full...
Hi, I am trying to make nrf52832 as a UART certal. The service UUID and characteristic UUID of peripheral are shown as the following picture. They are all 128bit and quite...
