Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
There are errors on Thingy52 "ble_app_thingee_s132_pca20020.emProject" which I built on SEGGER Studio for ARM V3.34 (64-bit) running on Windows 10. Please advise. Thanks....
Hi!
I'm using an NRF51822 as a GATT client to write data to a characteristic. The peripheral responds with several 20 byte indications. When I receive the indications, the...
Hi, I am importing a bootloader project that uses softdevice s110 and NRF51822 from Keil to Segger Embedded Studio. I have got all kind of errors during the process and I...
Hi Team,
In BLE5,
1) Can we connect a peripheral device to multiple central device?
2) Is it possible to check if connecton fails with any central device in perpheral...
I'm trying to put thingy_sdk_v2.1.0 and 10 nrf52832 boards. I'm compiling "ble_app_thingee_s132_pca20020.emProject". I don't know why it's always an error. How do I demonstrate...
Hi,
I'm using nRF52832 and SDK 15 and IDE im using is Segger studio.
i have ported the uart code into Ble_app_multilink_central.When i debug the code it is getting stuck...
Looking for an example on how to advertise for 10 seconds then go into sd_power_system_off. Trying this by using ble_app_template (s112, ses, sdk15.0, custom, 1 led, 1 rgb...
Hi nordic
I bought the nrf52840 board so I'm developing.
I want to use the this kind of LIR2032 coin cell 3.6v ( www.amazon.com/.../B074VX8ZJF )
I measured power of...
Hello, I'm experiencing frequent endless loops at 0x16cbc with s132_nrf52_3.0.0 softdevice and SDK 12.3 on a custom board with Aconno NRF52832 module. I'm using SAADC and...
Please can you help me with this fairly straight-forward technical query for a customer new to BLE.
Please can you advise which is the best way to structure the link in...
Hello,
I am currently working on the development related to RSSI of beacon using nRF51_SDK_9.0.0_2e23562(SDK). The beacons I’m using are developed with this SDK as well...
Hi guys!
I want to select NRF52840 as my target platform. Is it possible to start software developing on 52832 (for which I have devkit) and then seamlessly move my code...
Hello, I want to do a project with Segger Embeded Studio using the nRF52840 with the SDK_Mesh I have 2 nRF52840 cards and I want to transmit data to a mobile phone using a...
i compiled the ble_uart_app project it got downloaded in to the NRF51DK but the bluetooth is not getting turned on ,usually the output of this example is LED has to be turned...
Thanks for your support folks!
I am trying to read some bytes I have wrote in a MX25R8035F. From the datasheet, if you send 0x03 (READ) + 3 Byte address, then the memory...
