Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi.
I would like to measure the battery voltage using ADC in MCU. PCB has limited space, I consider to use the IC for this application.
The following is the LDO with...
Hello,
I am working on an IoT project using the Thingy 91 to send sensor data via Bluetooth to a remote device. Currently, I am trying to set up a simple beacon as shown...
Peripheral: SDK13.1 nRF52832
I don't want to change ConnectionParamaeter of Periperal by ConnectionUpdate request from Central. Can Periperal ignore ConnectionUpdate from...
Hej folks,
after quite some research on how to get Nordic UART and Linux together, here's as far as I got: Discover the device with hcitool lescan And - in theory - connect...
Hi all
Looking at the compatibility matrix, we understand that the following SoftDevices and SDK versions are compatible:
SDK 15.0 <---> SoftDevice S140 6.0.0
SDK 15...
Hello,
I am developing an app that uses Xamarin.Forms to communicate with BLE devices equipped with Nordic chips.
It works fine on IOS, but Android doesn't.
Android...
I have a custom board using the nRF52832 QFAA with SDK 15.3.0 and SoftDevice132 6.1.1. I'm also using an external 32kHz crystal for the softdevice clock. There are two hardware...
Hello,
I'm having issues connecting over TLS more than a single time. Using the nrf/samples/nrf9160/https_client works fine.
However, if you modify it to connect more...
Hello, I am trying to use the timer peripheral via registers only, however I am running into issues when I setup two timers and they activate at the same time. Here are my...
Hi There,
I am developing an IoT portable sensor which needs to operate across Europe Zone 1.
Talking with different MVNO it seems that NB-IoT and M1 coverage across...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0).
I need clarification if softdevice uses RTC and if so is the Errata 20 applicable...
Hi,
I am using nRF52832 along with Softdevice 6.0.0, SDK 15.0.0, Chip Revision 2 (QFAA-EX0)
I am looking into Erratas and working on the possible workarounds. However...
HI,ALL！
I use official routine development NRF52832，
NordicSDK\nRF52\nRF5_SDK_16\examples\ble_central_and_peripheral\experimental\ble_app_att_mtu_throughput\pca10040\s132...
Hey!
I'm using mesh sdk 4.0, nrf5-sdk 16.0 and run the serial example.
currently I successfully provision 2 light server with the ipython interface, and to configure them...
I am trying to do service discovery using the discovery manager library on any BLE device I connect to my central. I start the service with bt_gatt_dm_start(conn, NULL, &discovery_cb...
