I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh.
I based my development on the Light Switch...
It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
Hi,
I am currently implementing the protocol for a serial DFU, following the instructions given here:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hi all!
TL;DR
Is there a way to start 2 timers in 1 instructions ? (or to synchronize them afterward?)
- - -
Background
I need to take 8 timestamps of GPIO edges...
Hi,
I'm using S112 v6.0 with SDK 15.0 on nRF52810. It's based on app_ble_uart example. I have some data to save in flash. I define the address as follow:
#define PAGRE_TO_ERASE...
I want to extend the Thread Cloud Client Example (thread_cloud_coap_client_pca10056) with a peripheral controller. And I am looking at the UART Example (ble_app_uart_pca10056_s140...
Hi,
I will connect nRF52840 with other BLE module (ESP32) and they must exchange data (at first aproximation 20-50 bytes each 1-5 seconds).
I need to acheive lowest power...
nRF52 DK,software is nRF5_SDK_12.3.0_d7731ad,I'm using the example of "ble_app_multilink_central". SoftDevice is "s132_nrf52_3.0.0_softdevice.hex"
The BLE device is advertising...
Hi,
There is a racing issue in file: nRF5_SDK_for_Thread_and_Zigbee/components/iot/background_dfu/transport/coap/coap_dfu.c in function:
Sometimes calculated dalay is...
I'm trying to merge uart example in nrf5 sdk with light switch server example in mesh sdk
but I'm only facing these 2 errors :
when Linking uart_pca10040.elf:
Output...
Hello,
I'm usign nRF52832 with nRF5_SDK v15. I'm using "ble_app_uart" example. I just wanted to know that What is the wake up procedure of the MCU when we call the sleep...
Hi,
I have a trouble trying to start development process on my NRF52840 DK.
Following the instructions
https://www.nordicsemi.com/eng/Products/Getting-started-with-the...
The nRF Connect application can not search the device after I modified the Rx, Tx pin in my own PCB board.Can anyone tell me why?
The UART can run well,but the application...
Dear Sir/Madam,
I tried to add battery service to the sample "ble_app_uart", but the code doesn't send notifications to cell phone. I struggled for several days and try...
