I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Upon my first connection to my device with LE Privacy, first connection meaning after I've reset the firmware, I'm unable to read anything. The write characteristic works...
I am trying to use a Raspberry Pi as a provisioner for nRF52 development kits. I can run the meshctl utility on Pi but I am not able to see the un-provisioned beacons on the...
My application running on top of the S132 has a data base which can store up to 12 hours of data (720 points @6 bytes each). A request is made from the GATT Client to retrieve...
I am getting following errors when compiling source code in Keil-5. Any one suggest me what i am missing to define symbol?
I have defined symbols in target>>c/c++ : BLE_STACK_SUPPORT_REQD...
Hi
I am trying to see log messages on the kiel debugger window or in the virtual com port window but nothing is not displayed. printf also are not displayed, nrf logs...
I am working on adding a periodic timer to an existing and running application to add some new features.
I mimic exactly what is done in the peripheral/timer_pca10028 example...
Hi there,
I've followed this tutorial SES Tutorial on setting up SES with the sdk but it seems that it's written for newer hardware? nrf52 chips?
I've gone through the...
Hello,
I am using nrf24l01+ module with atmega328p and transmitting 20 bytes data. Everything is working fine but some times it is not receiving data or transmitter nrf24...
Hello,
I'm newbie with BLE and nrf52382.
I was looking in other questions but couldn't find an answer for my problem.
Our board contains 2 external crystals: one of...
We need to add BLE CLI to our devices, so I'm trying the ble_app_cli example (with an nRF52 DK) and it is not behaving as I thought it would.
I see that it is in an experimental...
Dear All,
Now , we are preparing to development opensource code based on Nordic header files (nrf_xxx.h , nrf_saadc.h etc) , but we don't know if
this way will break Nordic...
hi
i am trying Light Switch Demo in Mesh SDK 2.0
I am using nRF52 4 Kits
on 1 Kit I downloaded Provisioner
on 1 Kit I downloaded Client
on 2 Kit I downloaded Server...
We've recently migrated to SDK 14.2.0. Our app, running on iPhone 6, sends the BLE_GATTS_EVT_EXCHANGE_MTU_REQUEST and the connection is made and works correctly.
On an iPhone...
After run the nRF Connect on my PC the CPU usage becomes very high (over 95% on the WMI provider Host service), then the PC does not performe any other task.
When I close...
