Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Is it possible to provision Bluetooth Mesh nodes at the factory so they automatically join an existing network? Our application is more industrial in nature and we don't want...
Hello,
I have a project on: Periperal: experimental ble_app_blinky / and Central: experimental ble_app_blinky c.
So, in the function of button-event-handle，we have already...
Is there any information available on the radio address matching in the nRF52832?
Specifically I need to know how many (if any) bits of error are allowed in the received...
Hello,
I just wanted to report some strange behavior I've observed in my application. The bootloader timers stop working when nrf_delay_ms is called. In my case this could...
hi Nordic Team
The Document regarding Light Switch Example says following
The provisioner configures Button 1 on the client board to control the first server, Button 2...
Hello. I have 2 boards with nrf52832. I want to make 1 of them peripheral and the second one central. So the central board will connect to the peripheral board and send data...
I try launch example Nordic UART and get error: Error 133 (0x85) GATT ERROR
I need use stack for nRF51822 without external 32KHz crystal.
Here -> softdevice work with...
Here I am working on NRF52832 + SDK15。
I have designed two board with different 52832 package ( N52832-CIAAB0 and N52832-QFAAB0 ), I have disabled all peripheral part and...
I am using nRF51822QFAA & S120(v2.1) & SDK10.0.0
The application is to scan nearby ibeacon and send the ID information by UART. But the application always hang / reset...
When the nRF52 micro-controller is programmed through batch file i.e. nrfjprog utility, the flash fds fails to initialize.
Every time, flash fds initialization fails, I have...
Hello,
I am new to BLE as a technology and have a question regarding how Peer Manager handles bonding.
As I currently understand, the function of bonding is to enable...
I want to turn on the LED in Thingy:52 in a particular color if a particular condition is satisfied. How can I address the LED and turn the LED on in the desired color in...
Hi,
I am using the UART exmaple as a skeleton code to get RSSI from a peripheral nRF52 DK. I am working with the SDK V14 and I want to integrate my code with an arduino...
Hello, Nordic engineers. Thank you so much for spending your time solving my problem.
Currently, a custom board is made with the Nordic nRF52832 chip. As I have studied...
Refer to this post ， I did the same job to change simple_on_off model into generic OnOff Model , and I could control the LED state with nRF Mesh application as well.
I have...
