Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
I am using nrf52832 with sdk11 and s132.I am using ble_app_beacon example wherein I want to advertise with different address after one power cycle.
In ble_stack_init...
I have uploaded the Image with Keil µVision compilation errors, included Files in main.c and on the left side the compilation of micro_ecc_lib_nrf52.lib file using " build_all...
Hi there,
I'm trying to do a DFU over BLE using the Nordic nRF5x SDK on version 14.2. I'm using an NRF51 dongle on the PC side while trying to transmit to an NRF52832,...
I am using a nRF52 to communicate using both BLE and proprietary protocols. When using BLE, I apply the workarounnd for errata 102 and 106. However, when I switch to my proprietary...
Hi
We are using PCA10040 together with the ble connectivity firmware, pc-ble-driver and pc-ble-driver-py as a part of our automated test system. Eight dev boards are connected...
Hi,
I've been trying to update Espruino ( github.com/.../Espruino) from using SDK 12 to SDK 14, which is proving to be a pretty horrific task.
The latest issue I've...
Hi,
I am currently porting an application s110-based to s130v2.
Previously, I used to create critical sections using sd_nvic_critical_region_enter/exit .
Reading...
Hello,
I am using nrf52840 PDK, sdk 13.0.0 for my college project. I am trying to rewrite this nrf mpu example , in order to read data from MPU9255 and observe the data in...
Hi l trying to hookup arduino primo and BMI160,but recently my develop is in a strange situation,that i sent 0x00 and others register but alway return 0xff, here shows the...
I want to check if some errors happened during the initialization before entering while(1) loop in the main. I am using nrf_CLI in my application (SDK 14.2.0 and S140 on nRF52840...
Dear Nordic Team,
Tanks for Supporting.
How to start test DFU in SDK12.3.0. My Hardware is PCA10028.
How to merge hex files soft device and bootloader ?
update 1...
I need to count millis from nrf52 start
I have seen that all are using rtc1 but I did not find any example from which i can integrate it to my project.
We are in the development stage of a product that uses the nRF52832 and have acquired a nRF6707 Rev 1.1.0 power profiler kit to make power consumption measurements.
I am...
Hi,
I'm trying to download Invensense's "Embedded MotionDriver 6.12" in order to compile the Thingy:52 SDK, as suggested here .
It seems that this wasn't previously...
Hi everyone,
I am currently trying to implement USB headset on nrf52840. As far as I can see the audio example from SDK14 uses SyncType=None meaning that bmAttributes bits...
