Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hi all,
I am not very proficient in NORDIC and BLE. I was wondering if you could answer me.
I am developing a module using NRF52. I have a redundant wireless communication...
I am using a PCA10040 with a nRF52832 mounted on it. I am trying to match the IC revision with the packet variant as explained here .
The problem here is that the chip...
Hi I am new to Nordic development and set up all the tools required for compiling and flashing program to nrf52840 0n ubuntu. I downloaded nrfjprog and jlink segger and put...
Hello,
I'm trying to use a nrf51 dongle (PCA10031) as a BLE sniffer. I'm following the ble-sniffer_win_1.2_User Guide.pdf.
On the required software, i need to install...
Hi,
I try to use the example ble_peripheral -> blr_freertos -> ble_app_hrs_freertos and I add to the thread a fds_register() and fds_init(). Problem: In the call back function...
Hello, I am using the NFR52 DK (s132) in peripheral mode. I have implemented a pairing mode based on a static passkey. However, the available time to enter the key in the...
Hi,
is it possible to atomically change both the GAP address and the advertising message in one step? I want to broadcast two different advertising messages with each of...
hi,
please any one explain me, what is the use of power registers of module such as UART, SPI, ADC,GPIOTE etc..
1.NRF_GPIOTE->POWER
2.NRF_ADC->POWER
3.NRF_UART0-...
Hi guys, now i have done the example as the light control demo description, but i have a question about that how i can let the light server to leave the network? Thank you...
A little background with this question
So, long story short:
To send data using notification, in android, you must first enable CCCD descriptor of matching attribute...
we have made 51822 communication with 24LU1+ successfully, result is 32payload, 2Mbps, 800FPS。
however, after add freeRTOS, our 2.4G will lost 5-8 packets and disconnected...
Hello,
I'm having a lot of trouble debugging some errors on UART. I'm initializing the UART as follows:
void uart_init()
{
ret_code_t err_code;
const app_uart_comm_params_t...
Hello Everyone,
I'm a beginner for nRF52 and my aim is to learn and develop system on nRF52. I have bought nRF52 development board and installed Keil MDK on my system....
I have to talk to a SPI device, which gets an address and then needs some time to handle the address. Afterwards the transfer can continue.
Is this scenario possible to...
