Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hi all,
I'm working on a custom board based on the nRF9160 and using nRF Connect SDK v3.0.2. We’ve developed the board in-house and integrated the npm1300 PMIC as part of...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
I know this question has been asked many times, but none of the solutions I've found have solved my issue.
Nordic Dongle PCA10031 V1.1.0
Master Control Panel 3.10.0.14...
Hi,
My project cannot be debugged using Segger Embedded Studio. The debugger doesn't halt at the application main and instead keeps running. Hitting a pause shows the debugger...
Dear all，
We use thingy's microphone collect data and transmit to Android mobile by BLE, and need no loss of reliable data transmission.
How to do?
Thanks a lot.
I have developed custom PCB with nRF52832. My antenna layout is very similar to layout present on nRF52DK (PCA10040). All works well. Now, in next prototype, I want to add...
I designed the NRF8001 into my circuit board and my application processor is connected to it. Now I need to develop my application program such that I can transmit and receive...
Hi,
I am working with the Red Bear BLE Nano 2 (nrf52832) and programming it in Arduino IDE .
I am trying to merge the BLE_HRM example with a TWI example to be able to...
Hey,
I have a problem with receiving data on my Android app.
I'm sending several data via Services & Notfication Characteristics from my NRF52840 Application to my Android...
hi,
I have some problems about pwm register.
1.NRF_PWM0->MODE
2.NRF_PWM0->COUNTERTOP
3.NRF_PWM0->LOOP
4.NRF_PWM0->DECODER
5.NRF_PWM0->SEQ[0].PTR
6.NRF_PWM0-...
I use rRF52832. After doing "Flash Tab -> Erase" of Keil's development environment, it became impossible to connect at all. I tried using nRF 5x Command Line Tools (nrfjprog...
I'm trying to port the _12.3.0_ DFU bootloader_secure example to my custom nrf51822 board.
The example can run perfectly on pca10028 board, but not on my 51822 board even...
Hi All,
I am developing an application on nRF52840 Preview DK which does not need the Soft device. But it needs the MBR to run a bootloader for Firmware update purpose....
Hi,
Now I am using nRF52382 to make a product which needs a accurate one second timing. Then I use the project "nRF5_SDK_15.0.0_a53641a\examples\peripheral\rtc" and "nRF5_SDK_15...
Hi there!
Device: nRF52 DK
App: nRF connect
Compiler/IDE: Segger Embedded studio
SDK version: 14.2
Soft device: s132
Problem description: I am trying to run blood...
Hi,
I am reading a BMX055 via I2C which consists of three sensors with three addresses.
I got the easyDMA running to read 10 times the gyro using the PPI and the data...
