Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
Hi,
Greetings!
I just tried Low Power Node example application from SDK for mesh 16.0.0
It works functionally well, however I am little curious to know below point(s...
Hi,
I start developing with a new MacBook Pro (2019) which only offers USB-C ports. Currently I am facing the issue that the Programmer App does show the connected Thingy...
Hi!
I have recently setup the development environment for my Thingy 91 on Windows 10 environment using nRF Connect Getting Started Assistant. But I am having some trouble...
Hi, I am working on nRF Thingy52 for a week. I am having SES with SDK_16.
I am having 3 nRF thingy to do a testing purpose
First i need to analysis how the thingy works...
I'm testing using the internal RC circuit to drive ble via the S132 softdevice. Set up is with Nrf52DK and Power Profiler kit. I got everything running and was measuring about...
Hi, How can I configure the LwM2M server (URL, Port, Credentials) on my Thingy91? Can I do this via MQTT and the nrf Cloud or do I need some specific tools?
I have a GT832C.01 (Bluetooth 4.0 BLE sensor detection module BMX055 9DOF NRF52832), I don't know how to program it, I can see it from the phone, but what software do I need...
I have a BLE board with a nRF52832 and some peripherals. It came with a preinstalled bootloader and firmware (the bootloader supports DFU via BLE to upgrade the bootloader...
Hi,
I am completely new to this technology,I need to interface BME 680[humidity,pressure,gas,temp sensor] with Nordic nRF52840 - how it is possible,i want know the hardware...
Hi,
I am using nRF52832 DK, with Segger Embedded Studio as IDE. I am using ble_app_uart example. I have used an encryption algorithm. The encryption algorithm is called...
Hi,
Does the SPIS generate interrupt for every byte of data receive ?
What kind of interrupt of event that SPIS will generate for data received ?
Please advise
Hi,
I need to assign Rising edge and Falling edge event in a single pin.
I try to assign both Rising Edge and Falling Edge event into APP_EVENT_PIN.
There is a error...
Dear all,
I have noticed that NRF_LOG_FLUSH() function is used in many examples after each nrf_log print function. In some cases though, the program freezes when I try my...
HI!
nRF52832, SDK13
I need to know what happen with setted output RF power when peripherial devie connect to central device.
For example, if output RF power setted to...
