RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Hi,
Greetings!
I just tried Low Power Node example application from SDK for mesh 16.0.0
It works functionally well, however I am little curious to know below point(s...
Hi,
I start developing with a new MacBook Pro (2019) which only offers USB-C ports. Currently I am facing the issue that the Programmer App does show the connected Thingy...
Hi!
I have recently setup the development environment for my Thingy 91 on Windows 10 environment using nRF Connect Getting Started Assistant. But I am having some trouble...
Hi, I am working on nRF Thingy52 for a week. I am having SES with SDK_16.
I am having 3 nRF thingy to do a testing purpose
First i need to analysis how the thingy works...
I'm testing using the internal RC circuit to drive ble via the S132 softdevice. Set up is with Nrf52DK and Power Profiler kit. I got everything running and was measuring about...
Hi, How can I configure the LwM2M server (URL, Port, Credentials) on my Thingy91? Can I do this via MQTT and the nrf Cloud or do I need some specific tools?
I have a GT832C.01 (Bluetooth 4.0 BLE sensor detection module BMX055 9DOF NRF52832), I don't know how to program it, I can see it from the phone, but what software do I need...
I have a BLE board with a nRF52832 and some peripherals. It came with a preinstalled bootloader and firmware (the bootloader supports DFU via BLE to upgrade the bootloader...
Hi,
I am completely new to this technology,I need to interface BME 680[humidity,pressure,gas,temp sensor] with Nordic nRF52840 - how it is possible,i want know the hardware...
Hi,
I am using nRF52832 DK, with Segger Embedded Studio as IDE. I am using ble_app_uart example. I have used an encryption algorithm. The encryption algorithm is called...
Hi,
Does the SPIS generate interrupt for every byte of data receive ?
What kind of interrupt of event that SPIS will generate for data received ?
Please advise
Hi,
I need to assign Rising edge and Falling edge event in a single pin.
I try to assign both Rising Edge and Falling Edge event into APP_EVENT_PIN.
There is a error...
Dear all,
I have noticed that NRF_LOG_FLUSH() function is used in many examples after each nrf_log print function. In some cases though, the program freezes when I try my...
HI!
nRF52832, SDK13
I need to know what happen with setted output RF power when peripherial devie connect to central device.
For example, if output RF power setted to...
