Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Hardware:
PCA10040
V 0.9.0
2015.47
Hello,
I connected the above development kit to my PC today and was prompted to update the J-Link firmware ("Strongly encouraged...
Hi,
I am using SDK16.0(ble_app_uart) program to sending dates between the phone and board.When I use my iphone xs max,it works on well.But it come out some faults when it...
I have a compile error currently: "section .heap overlaps absolute placed section .stack"
The heap size is currently set to zero.
I am guessing I am just going over the...
I keep getting this error code and while debugging I'm able to resume execution. This error seems to be thrown during my DMA transfers over SPI. Is there somewhere I can look...
I have a Thingy 91 and trying to connect it to nRF Cloud without any success so far. It is not connecting to GSM Network.
I updated both modem software and application...
At least using the LLD linker, it is possible to locate RAM segments of known size (.bss, .data, heap) at the end of RAM. Normally this allows placing the stack under these...
Segger Embedded Studios 3.52, nRF5_SDK_for_Thread_and_Zigbee_v4, nRF52840 custom board
Hi,
I use this code to start network formation on Zigbee:
zb_bool_t comm_status...
I've had nothing but trouble attempting to get the SUPL library work. I finally was able to get it working on the 9160DK with the latest modem software and GPS sample. However...
Dear All,
I am experimenting with the nRF52840 DK and the ble_app_template . Based on that project, I am trying to configure a pin interrupt on Button 1 (pin 0.11). This...
Hi,
The project I am working on involves streaming 8 audio streams (16 channels of data), and I was hoping to use the nRF52 for this purpose. Does anyone have any ideas...
When we test the BLE conducted power, we find some phenomena, when IC power is setted to 0dBm, the active power loss is similar with passive path loss, it is consistent with...
Hi,
I would like to save my project and add something like a version number to it. I use an example from nordic SDK. So in my case I use solution from ...\examples\ble_peripheral...
Hi Guys,
I am trying to enable LESC Encryption, but I do not understand how to generate keys_own.p_pk and DH keys.
The sequence is the following:
1. I receive BLE_GAP_EVT_SEC_PARAMS_REQUEST...
Hi,
We want to implement periodic advertisements on nRF52840.
We use:
1) nRF5 SDK ver 16
2) Softdevice S113 ver 7.0.1 (but this can be changed if required)
Does...
I am looking into automating the programming steps for the nRF9160 and nRF52832 for a production environment. I would basically like to do what the nRF Connect Programmer...
