Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I tested with Light Switch Example in nrf5_SDK_for_Mesh_v3 version, I have set Transittion time to 160 second and Delay to 0, problem occur is the device Cann't countdown...
Hi,
I am using an nrf52840 MCU, Nordic SDK 16.0.0 and IAR Workbench for ARM v8.40.1.
The MCU has the following configuration:
- MBR installed
- DFU secure bootloader...
Hello everyone,
I faced with bus fault after running beacon example from mesh_sdk. It occurred after calling mesh_provisionee_prov_start().
Unfortunately, I didn't found...
Greetings...
Provisioning w/ Android tool only works when board is connected to debugger.
Provisioning failed to even find the devices when scanning after disconnected...
When enabling 3 instances of SPIM (1,2,3) on NRF52840 the application doesn't start at all.
Weirdly however, the application works fine when SPI3 takes SPIM3 and the rest...
Hi,
Does SoftDevices v7.0.1 supports Multiple Advertising Sets feature? I read that Softdevice v6.1.0 does not support the Multiple Advertising Sets feature. Let me know...
Hi. I was wondering if maybe you know where can I find the PCB desing of any of this modules: NRF24L01+ (the black one) or the SMD version. I only can find those pictures...
Hi gays,
Now, I want to c ollect a pulse waveform(example : 1s, 50% duty cycle ) which accuracy requires milliseconds resolution and I use PPI to read a capture value from...
Hi,
We have a custom board that uses an nRF52840. All our development is done on Win 10 based PCs. Our custom board is connected to our Win 10 based PC via USB and when...
Hello Sir,
We are using NRF24L01+PA+LNA SMA Antenna for transmission purpose using arduino using RH_NRF24.h library.
It is been set to 0dBm transitting power by default...
Hello,
I am working with nRF SDK V 16.0.0. I am using peer manager for my application, can I store my application data too using peer manager? if yes, please help to do...
I try to create coap server project and it should by updateable by DFU. I merge project simple coap server and thread dfu client, and I keep instructions in documentation...
Hello Everyone,
I am Using Nrf51822 module and s130_nrf51_2.0.1_softdevice . my actual function nrf51822 twi interface with stc3115 Gas gauge IC .read the battery voltage...
