Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
When using the BLE device, BLE_GAP_EVT_DISCONNECTED event informs us that connection between dongle and BLE device was closed/lost.
Is there a way to know when dongle connection...
Hi
New to using EGU, trying to use it to implement software interrupts. How do I capture an Event?
I can see how to trigger and clear an event using -
nrf_egu_task_trigger...
In the function ble_init, I am getting an undefined reference to sd_softdevice_enable during the linking process. I see that in nrf_sdm.h there is SVCALL(SD_SOFTDEVICE_ENABLE...
Hello,
I am looking for the cost effective simultaneous central+peripheral solution using nrf BLE.
The nrf52810 seems to be hardware capable of doing this but I am...
Hi, I am creating custom ble service.there i need to perform
1. character - READ , NOTIF
2. character - WRITE READ
3 . character - READ,WRITE, NOTIF
I achieved ...
Hi
I'm on a custom board with NCS 1.2.0 and modem firmware 1.2.0.
We have implemented agps, and testing with 2 units with agps colocated with 1 unit without agps. All...
Strange device crash on deprovisioning.
This is probably something incredibly stupid, but I have been fighting this problem for a week and don't know where to turn.
I...
Hello
I program the example code peripheral " ble_app_hrs -pca10040e -s112" on nRF52810 and central " ble_app_hrs_c-pca10040 -s132" on nRF52832 .
I used nRF Toolbox on...
Hi,
we are working with Nrf52 and do not need/use Bluetooth, i.e. our devices will not have the Softdevice stack installed.
I was informed that for the radio certification...
Hello, I am using nRF52840, SDK 16, SoftDevice s140 with SES. I want to configure my device first in connectable mode and then in non-connectable beacon mode. sys_advertising_init...
Hi,
The situation is very simple; I try to use the CoAP Utils library to simplify CoAP usage in an application running on the nRF9160 DK ( https://developer.nordicsemi...
Hello,
I’m using the ble_app_multirole_lesc application from SDK 16.0.0_98a08e2 as is (not modified) on 2 PCA10040 dev kits but unfortunetly both boards return a disconnection...
hi, nordic support
SDK version is 15.3.0
the example is ble_app_uart_c
I have modified the project based on this address： https://infocenter.nordicsemi.com/index.jsp...
Using nRF Connect SDK v2.1.0 and the nRF5340 PDK, are any of the ble mesh samples in the fw-nrfconnect-nrf repo working yet? I've tried both the mesh light and light_switch...
