I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
I have an in memory log variable that I write to on various BLE and device manager events. If there is ever a serious error, my implementation of app_error_handler() now takes...
Hi,
I have programmed the radio_test_example to target having nrf51822 qfacaa chip. I have changed the UART pins as per the custom board.
It's working fine but showing...
Hi,
How can i wake up(interrupt) the nrf51822 device from "air" (from my iPhone application)?
For example after i paired iphone with nrf51822 i want to put the nrf to sleep...
I am using SDK 7.1 and I am attempting to use the Makefile.common found in sdk_7.1->components->toolchain->gcc->Makefile.common. However, the Makefile.common appears to contain...
I'm trying to send multiple 20byte notifications per interval through the NUS usart service to iOS 7.0, 30ms conn. interval in the UART demo app. It seems I cannot tx more...
Hello,
I'm working on a project with SoftDevice s120. I played with the project ble_app_multilink_central. The maximum number of characteristics per service supported by...
Our application includes a 32.768 kHz crystal oscillator with a nominal +/- 20 PPM accuracy. When I factor in aging over 10 years and worst case variation due to temperature...
Hi !
In questions question1 & question2 Petter Myhre gave a complete answers about count of max characteristic per service in s120 and how to resolve this restriction....
Hi,
I am now developing the BLE with our company's own sensor, so we are not using the motherboard. There always a problem when we use it. I am using the PCA10004 board and...
SourceCode_SSDI_BTLE_BeaconReceiver.zip I am starting to use the Nordic chips, and have a PCA10004 board running. I have modified the experimental_ble_app_multiactivity_beacon...
Hi Nordic,
I am a hardware/firmware guy without App development skills and I also lack the time to acquire these skills. I enjoyed your UART App during my development,...
Hi all,
First of all, I'd like to express how pleased I am using this development kit. The easiest ever to start with, well documented and most importantly I can use the...
hii...
am using nrf tool box app in my iphone. i have tried to use dfu feature.i flashed softdevice and bootloader hex file to he evaluation board and in i phone app i...
In the "NRF51 Series Reference Manual" (v3.0) it states:
The LPCOMP shares registers and other resources with peripherals that have the same ID as the LPCOMP.
You must...
