Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
I'm new to the Nordic range of devices and the SDK.
I have a project where I'm using the HAL in the SDK to configure GPIO/GPIOTE and the UARTE0. With both the GPIOTE and...
Just want to check that my understanding is correct:
I have ported/migrated my app from SDK 6 to SDK 9, merely because I want to use the DFU facility. However, I have read...
Hello everyone
i am trying to add printf statements inorder to see the excution of the program can anyone sugges tme how to printf statemtns in app_uart example!? i would...
Is there a document describing the interaction and any asynchronous issues with the different types of event handlers? As I read it there are softdevice events, BLE events...
Hello,
I have added a timer to my code, which I need to be of 1ms. The handler of the timer is correctly called when the timer is 5ms or above. However, if I change it...
Hello,
After searching in forum, I understood that we cannot debug application with softdevice unless PRIMASK bit is set.
But in my application there is a requirement...
Hi Nordic
I am using GZLL to develop a prototype whereby data from sensors will be transferred to a Computer in a Wireless sensor network.
The idea is, when data are requested...
Dear all,
we want to use a nRF52837 for a developement project we are planning. We have been asking ourselves on which functional level the alpha Softdevice S132 for the...
Hello, i analyze the device manager routine (device_manager_peripheral.c) and in BLE_GAP_EVT_CONNECTED case you checking containing the device address in bonded table.
My...
I am working with nRF51822 beacons and an iOS 9 application that I am developing. I am testing on an iPhone 6. My application uses the CLLocationManager's beacon ranging functionality...
Hi,
I want to use the whole payload of the advertising packet. I decided to use the manufacturer specific data. BUt I cant´use the whole payload by myself. I get this payload...
dear all：
I use the spi slave mode. i have a question,pls help me.thanks.the questions as follow:
I want to distinguish instruction type, and then reply to the corresponding...
Hello,
I am working on nrf51822 SDK 9.0 and softdevice 8.0 . I got the application note to create a custom profile for SDK 5.2.0 and softdevice 6.0.0 in nAN-36_v1.1 . ...
Hi: We develop our program based on (nrf51822 QFAAG0 1403AL), I found a serious problem that our new IC is (nrf51822 QFAAG2 1415AF), and the old program can't run on it any...
