hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
I'm trying to include the SPI driver in my project.
I have added the .c file into my project:
I have included the path into the project:
I have enabled the SPI...
I try to make bootloader via USART for my application. I'm using: nRF51422rev.2, SDK6.1.0, S210 ver3.0.0. KEIL5.11. I did everything like describes in post here:
devzone...
I want to implement BLE security in one of my project where central and peripheral connection should be secured rather than only characteristic protection.
And any way to...
I'm developing a custom driver (C++) for the SPI master. Somewhere I've made a mistake, where the first received byte is written with a memory offset in SPI mode 1. I.e. we...
Hi,
I have a BLE application, which I want to interface with PC via serial communication through USB.
It seems that just adding Softdevice breaks the USB_CDC_ACM example...
Hi all,
As a followup of this question, I started with the Thingy Mesh Provisioning Demo v0.5. However, I cannot get this version working possibly due to some unclear points...
Hi,
Am developing a beacon using nrf52810. I have a doubt on how to program the nrf52810 which I made using the schematics and layouts given in the Nordic website for nrf52810...
I am noticing that FDS requires me to specify a "record size", but there is no maximum specified, so I am testing it. Currently my program attempts to store 32 words, but...
I want to add some code to static void app_onoff_server_set_cb(const app_onoff_server_t * p_server, bool onoff) in light switch server application.
My intention is when...
When nrf51422 passed the authentication, when entering the rx mode of DTM, there was always a -59dbm launch at the 2.79GHz frequency point, what caused it, and how to eliminate...
Hi, I am trying to interface MPU6050 IMU module with NRF52832 DK.
I need to send the Accelerometer and gyroscope data to mobile app by using BLE_UART program
this is my...
Hi,
I'm trying to send a broadcast message from my client to all my server. Actually i'm working over a modifed version of the light switch example.
i saw that in the...
Hi i am using nRF52832 with SDK v14.0.0 on LINUX, so usually a service and a characteristic have the same name space but you just change a few bytes for every id. But the...
Hi there,
I am having issues to run my program after a MTU increase size.
I am getting the following error:
I am not sure if it is related to the RAM size values...
