Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hello everyone,
I'm currently trying to change the connection parameters to be quick(100ms 0 slave latency) on a button press and after a timer timeout I go back to the...
Hi,
I have some problem. My code was working and everything was fine, but I decided to improve my program. I made some changes, and now TX_DS interrupt on PRX side doesn...
Hi.
It appears that the common gcc makefile in the current SDK does not work for S120, or S310. Please see the patch that fixes the problem.
Tested with S120 and blinky...
We are looking to add some device info into the advertising package, or scan response package depending on space. When looking for a way to do this in a standardised way I...
Hi.
I'use nrf51822 beacon kit and android nrf beacon app.
I'm modify nrf51822 beacon example source code,
I hope
1.I eliminated the button
2.After I turn on the...
I'm new to nRF51822 Evaluation Kit. I was able to build the hex from "ble_app_hrs" example with GCC and Eclipse. However, it won't allow me to flash it by drag and drop to...
Hello, I'm an developer using nrf51822.
I have the same problem with this.
devzone.nordicsemi.com/.../
But this problem has no more discussion...
Here is my problem...
First I load soft device through nRFgo.
Then I run debug with eclipse.
I then step through code in main.c ...
(I'm using QFAAG0 chip)
Stepping worked fine when I used...
Hi,
I use a system with BLE softcore running - and can generate highly precise pulses with the gpio pins using Timer1+2 with interrupt service routines. Jitter might be...
Hi,
I want to use nRF51822 to do some development in the eclipse.I follow the document(nAN-29 nRF51 Development with GCC and Eclipse Application Note v1.1) step by step,when...
Using PCA10001 Evaluation kit, SDK v6.1.0_b2ec2e6 and SD s110_nrf51822_7.0.0
IOS app nrf Toolbox HRM on iPhone. Everything is working fine, get the advertisement, connect...
Hi all,
Short version: I want to make 200 devices using nrf51822 (and S130 v0.5.0-1alpha), all advertising/scanning at the same time, and process RSSI readings for proximity...
I am trying to find out what is the difference between nRF51822-mKIT and nRF51822 EK . Visually both of the boards look identical and the only noticeable difference is an...
I just tried setting up on Windows8.1 but can't see the "nRFgo Studio".
I got as far as step 4 on page 9 of "nRF51822 Development Kit User Guide v1.4",
but it doesn't...
