Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
I use two PCA10040 for nus experiment, S132, SDK14.1
sniffer capture packets found that no data can be captured after the master send CONNECT_REQ, I guess it is not because...
Hello,
I have a working application on nrf52832, running sdk version 15.0 and SD132 version 6.0.0. Now I would like to add dfu functionality. I followed the instructions...
I followed this :
Connect the nRF5 boards to the USB ports and decide which one you want to use as a client and which one as a provisioner by noting down their 9-digit Segger...
Hi all,
I want to verify nRF52840 SoC SPIS peripheral on PCA10056 DK using any compatible SPI master hosts. I use SDK v15.2.0 SPIS example.
I know that Nordic SPIS peripheral...
Hello All
I'm trying to lock debugging/reading capability in my code. My system consists of a bootloader and an application beside the Softdevice and MBR.
What is already...
For simplicity, I extracted the Demo 1 routine from the "pwm_driver" example which has 5 demos 'cause I thought it is simpler.
The code is shown below:
Can you please...
Hi, i want to build my ble app with softdevice. A s a result, I want to have a single .hex file that contains the sofdevice. And i am going to flash it to the nrf51822 using...
I have PTR9818 module and NRF52840 Development Kit. I flash firmware CLI example(SDK for Thread and Zigbee 2.0.0) for PTR9818 module and communicate with PC use USB-USART...
Hallo,
Currently I'm investigating different Low Energy Bluetooth solutions for our healtcare products that we build in Televic Healthcare.
So here is the setup I...
Hi all,
I'm a little bit confused with the Thingy52 SDK.
The "ble_app_thingy_s132_pca20020" code is the same of the "thingy_v2.1.0.HW_1.0" precompiled hex file?
Thanks...
Hello
I would like to know GPIO leakage current, especially when the GPIO outputs Low
state, leakage current flow thorough the High side MOSFET parastic diode.
If nobody...
Hey everyone,
I have measured input current by different transmit powers:
nRF52840
Equipment: Konstanter ssp 240-40 as current source
Agilent 34401Afor current measurement...
