hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
Hi,
I have a simple question. It is possible to use the ble-sniffer nrf51822 on Kali Linux? I found a guide to use it on linux but I don't know if it is the same for Kali...
I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
hi support team,
may i ask how to set static ip address for 7002?
1. i set these configs:
CONFIG_NET_CONFIG_SETTINGS =y
CONFIG_NET_CONFIG_NEED_IPV4 =y
CONFIG_NET_DHCPV4...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
Hi everyone,
I'm new to both nRF Connect SDK and Zephyr RTOS , and I’m trying to modify the official LittleFS FileSystem Sample to mount an external SPI flash as the storage...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
Hello Nordic Team,
Currently, we are performing power consumption testing using the Nordic nRF54L15-DK development kit.
As part of this, I aim to fully disable the Radio...
Hello,
I am using Nordic Thingy91 5G board. My modem firmware version is 1.3.6. My nRF Connect for Desktop version is 5.2.0, which has a Serial Terminal version of 1.5...
Hello,
I recently acquired a Thingy91 board in order to make a hardware prototype. I already have experience developing with the nRF52840 so I took inspiration from my working...
Hi
I cannot find the pin-configuration for the nRF9251 using the nRF91x1 SiP LTE firmware. I can see that the Thingy91X and the nRF9151-DK board are using different UART...
Hi,
We're planning to design a custom board using the nRF9151 for LTE connectivity. We'd like to add basic BLE support, with the following constraints:
The BLE chip...
We are trying to increase the TX output power on the nRF5340 when using Enhanced ShockBurst (ESB) . According to the product specification, the nRF5340 supports +3 dBm TX...
I'm develping my application with nrf52832 and nrf SDK v17.
I'm testing SPI interface so that I can use the external flash.
When I using SPI without BLE stack,the waveform...
Hi,
Our products have been mass-produced and now need BQB certification, but the certification fails.
IC：nRF54L15 ncs2.9.1
base project: ncs_v2.9.1\v2.9.1\nrf\samples...
