Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We are implementing a Joiner device using OpenThread on the nRF5340 (with Zephyr, NCS v3.5.99-ncs1-4). After successfully joining the Commissioner's network ("Join success...
Good evening and a happy new year to everybody.
Now it's time to work again, and I already stumbled about a little twouble while implementing a peripheral with concurrent...
Hey guys,
I'm designing an antenna for our open source sensor beacon, RuuviTag: http://ruuvi.com
Because we're using 1/4 wavelength monopole antenna, I'm considering...
for ble, scan of central device can get the RSSI value of the advertising device, but the inquire can not.
Is it right?
what's the different between them?
Hi,
I have made custom nrf 51822 board, I don't have LFCLK crystal i.e, 32.768khz. When i run ble_hrs example code in it , current consumption of my board goes to ~150uA...
Hi
In my application I need to transfer several paires of bytes to a slave device, and it's mandatory
for CS signal to go high between pairs. (This actually means I have...
Hi
I want to know why flash memory access should be scheduled in between the protocol radio event?
is there any relation between the flash access and radio opeartion physically...
Hello,
I am developing a wearable device that utilises nRF51822. Right now, I am having a problem because when the wearable device is connected to a new phone, it needs...
Dears,
I am designing a notification application. I would like to know what if I want to support both of iOS and Android phone, which example code of ble_app_alert_notification...
im following ( devzone.nordicsemi.com/.../) step to "Setting up a project for debugging in Eclipse"
i run the debug config and click suspend
then get some problems
...
Hi guys, I just want to share my iBeacon code (over s110) developed on nrf51 dev board under ubuntu. It works fine but please feel free to improve it and share it!
I developed...
In some case sd_nvic_SystemReset() can not reset?
nrf51822 S110.
for example:
void main(void)
{
sd_nvic_SystemReset();
do something;
}
It can do somthing!!
So sd_nvic_SystemReset...
Hi,
I have just bought NRF51822 without any extra peripherals(no motherboard/DK). Just plain Module like below image.
I am supplying 3.3V to VDD and also Connected GND...
Hi all,
I find a problem when testing the ANCS program. It seems that after you connect the device with ANCS with an iphone, you cannot connect the device with another iphone...
I built the ble_app_proximity project and down load into my board, it can advertise and can connected by the lightblue and the nRF toolbox, But i sent the hex value of 0x02...
I can get right value when I chose QDEC_SAMPLEPER_SAMPLEPER_512us in slow application ,but in my application my max data rate is more than 2k, so the QDEC value is less than...
