Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
I am using proximity profile for my custom board as a tracker.I would like to make the services read/write operations accessable only to my andriod app.Others can connect...
Hello,
Recently I purchased a BLE Nano Kit with MK20/ DAP Link USB Board - Bluetooth 4.0 Low Energy Module Development Board from Fab2Lab and I was trying to use the nRF...
Hello,
We are new in Bluetooth development world. We want to use Laird's BL652 module. At beginning we want to use smartBasic and later Nordic SDK directly. Is it possible...
HI Nordic Team,
I had a production run of 5000 units. Used nrfjprog script to program the nrf51 .
Used the following commands:
nrfjprog -f NRF51 -e
nrfjprog -f NRF51...
Dear all,
I have a project with a nRF51822 based on S110 and SDK10.
Almost everything is running fine, but every time I scan for devices, either by calling BluetoothAdapter...
Hi,
I am writing an application for nRF52832 that uses both Flash Storage and Flash Data Storage in SDK12.2. I want to know how to get the start and the end addresses of...
hello,will you please tell me which code i have to use in the sdk 12.2.0 for rf communication with nrf51822 and nrf24l01 .and also tell me which settings i have to do for...
Hi
I'm working on detecting voltage change direction(up or down) by using LPCOMP or COMP.
LPCOMP initiates as following settings:
detection: NRF_LPCOMP_DETECT_UP.
reference...
Hi,
in want to extend the DFU library (Android and iOS) with a function similar to setBinOrHex(). But instead of a filename, i want to give a byte array with the init packet...
I think there is a bug in Nordic provided code in this thread about fetching the offending PC in a hardfault handler:
devzone.nordicsemi.com/.../
The provided code is...
I have found these 2 threads in this forum regarding this matter but I am a bit stuck.
devzone.nordicsemi.com/.../
devzone.nordicsemi.com/.../
I want to port the...
It's been 14 months since the nRF 5x IoT SDK 0.9 was released.
Given Nordic's normal release cycle, that's an eternity!
Will there be another release or is it dead now...
Hello community,
Before I was using a pca10040 by Nordic evaluation board. The project, that i developed, is running well using the EB but when I change to sparkfun breakout...
