I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi team support,
Got a problem with project ANCS and more precisely with the bonding and the Flag "allow_repairing" which was false and set by myself to true. But on SDK14...
Hello,
I'm trying to enable the monitor debug mode work with iar but I have some doubts about the address used in the EnableMonMode.mac macro provided in one of the blog...
Hi all,
I'm using nRF Sniffer (2.0.0-1.beta), i didn't have any problem for follow connection between master and slave but now, I have a problem with time displayed in...
Hi,
I need to use the radio timeslot api in my application. I'm using nrf52 ,SDK 14.0.0 and softdevice version 5.0.0 . I've gone through the tutorial for setting up timeslot...
Hello,
I'm testing PHY coding (for long range), I'm pretty surprise from what I get when I scan the RSSI of bluetooth channels (with Nordic app).
This is my set up:...
i want to erase and store the flash after detecting the radio active.
The radio signal is also active, when i erase and store .
Do erase and store the flash may influence...
Hi there,
I try to using nrf sniffer for trouble shooting, and follow the "nrf sniffer user's guide v2.0" , when I copy the unzip extcap's content to the Wireshar's Extcap...
Hi!
i am thinking about cut off uart when data is not transmitting.
As a method 1, i am thinking about using CTS and RTS Pin which is hardware flow control!
①Is this possible...
I'm using the nRF52 DK with mbed, running the heart rate monitor demo app.
When I disconnect the board from the PC and attach a USB power supply instead, the nRF52 won...
Hey all,
I'm working with the nRF51822 (nRF51dk) on a mac running high sierra, and I've been following this tutorial to try to get started. But when I try to make flash...
Dear Nordic engineer,
I try to setup Wireshark sniffer with nRF52-DK. I followed by nRF sniffer user guide v2.0.
I see interface toolbar of nRF sniffer on Wireshark. But...
Is there a block header information available that I can read thru the flash read function (e.g. in ble_flash driver, ble_flash_page_read() function ) ?
My FS (file system...
Hello,
I would like to understand the reason behind getting a error,(0x04) NRF_ERROR_NO_MEM , when calling the function
sd_ble_gatts_characteristic_add(p_service->service_handle...
I'am realy new to nRF52 development. I want to start with a simple demo as shown on www.nordicsemi.com/.../Getting-started-with-the-nRF52-Development-Kit.
What HW do I...
Every time I change a common source file within Kiel, the source file is changed for every project because (obviously) is a file common to all example projects.
Is there...
