I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
The data is sampled at 3khz, each sample is 2 bytes, connection interval is 7.5ms ,4packets per connection interval. The data is displayed on a graph with respect to time...
When I execute nRF5x_MDK_8_7_1_IAR.msi from the SDK 11 directory the files from the .msi are added to the IAR install directory, not the SDK. These changes are ignored when...
I was little bit confused between NRF24l01 and (+) plus version which is better . i want range of 900-1000m. which is best??
If i choose NRF24l01+ what are the ways to...
(/attachment/0495424521df76d5b8f8e66c969ed791)Hi,
I add ANCS Service into my Heart rate ref ble_app_ancs_c example code.
I use MCU nRF51 and SD130 in nRF5_SDK_11.0.0_89a8197...
Hello,
My device is based on nRF51822 SD110 v8.0. Softdevice is enabled, but no BT functionality used. I measure 2 different voltages with ADC each second with two channels...
I'm writing code for PCA10040 basing on UART/NUS example. There are no big changes: different UUIDs and just one characteristic for both reading and writing. I can connect...
This is a follow-up question from devzone.nordicsemi.com/.../
I finally got passkey support to work on ble_app_uart but don't quite understand the changes made to the code...
I am trying to add static passkey pairing to ble_app_uart in SDK_11 s130. To do this, I first implemented static passkey successfully in ble_app_gls using sd_ble_opt_set(...
Tl; dr
I tried to use OTA DFU with Public BLE Address, but I failed. Is this possible?
Details
Condition
I modified ble_app_hrs example like below (SDK11, pca10028...
I have a radio board using a NRF51822 with a custom radio protocol. I need a unique identifier, ideally 24bit, 32bit but be acceptable.
I notice in the parameters there...
I've looking through as much of the documentation I as I could to read more about the radio timeslot api.
I looked through the SDS document and the chapter on the Radio Timeslot...
I am able to use eclipse to run simple project, but after move the real one, getting lost of errors:
www.dropbox.com/.../Screenshot 2014-04-02 09.10.41.png
I add required...
Hello,
I just received my BMD-200 eval board today and cannot get any of the examples working. I started out trying to get blinky to work using GCC and the make files provided...
I am trying to port peer manager implemented in ble_app_gls to ble_app_uart using instructions in devzone.nordicsemi.com/.../ . I am using SDK_11 s130 on nRF51-dk.
I encountered...
