Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hello,
I was wondering what is the best example to take as reference in case I want to pair two BLE devices automatically, I mean, I would like to make my devices to start...
i use RTC wakeup the sleep mode,project used the uart etc.
uart baudrate set to >=115200 sleep mode normally.but is baudrate set to <115200 sleep mode at 50ms+- periodic...
I am trying to use nRF connect's advertiser feature to simulate some sensor output for my testing. The sensors use BLE advertisements with scan response to send out data....
Hello community,
I am working in a central device with SDK 13 v. 4, PCA10400 (NRF52832) and SD 132 and one task is to receive 30 bytes from a sensors as a notifcation,...
Hi,
we are using are more or less unmodified version of the Secure DFU bootloader example. Especially all BLE/Softdevice configuration in "libraries/bootloader/ble_dfu...
As mentioned here , my poor little Thingy:52 doesn't work after upgrading to version 1.1.0 through the iOS app.
After getting my Thingy:52 i played arround with it for...
I try to add function for the peer manager initialization and set the security parameters. I did not understand keypress and lesc parameters exactly. Documentation says for...
HI,
I am using nRF51822 by Keil compiler. I found if it was programmed with boot loader
nrf51422_xxac_s130.hex
by nRFGo Studio.
Then if download user code by Keil...
Hello!
I fill in a dis struct with the fields manufact_name_str, fw_rev_str and sw_rev_str. Everything is dandy and works perfect.
Then I also fill in the field serial_num_str...
In product spec for nrf52832:
Neg30dBm 0xD8 -40 dBm Deprecated
Neg40dBm 0xD8 -40 dBm
Similar stuff in the SVD out of SDK 12.3
When I convert the svd to rust (using...
Hi,
I am using NRF51822 and sdk12.2. I am using Softdevice s130 with peripheral experiment_ble_blinky example. I have merge UART example in this and it is working fine. ...
Hello,
We've stumbled upon a weird behavior on iOS making the smartphone unable to reconnect to our wireless device after a DFU from SDK11 to SDK13 (nRF52832): the notification...
Hi!
I am getting a HardFault when I try to read a GATTs value inside a GPIOTE ISR handler.
I already tried setting the ISR priority to low as suggested in various posts...
