Hi all,
I'm deploying an nRF9160-based device in India and hitting the familiar "which SIM actually works here" wall. Looking for current (2026) experiences, since older...
Hi all,
I've built a custom nRF9151 board, which is successfully responding to the basic factory AT commands. It won't accept a CFUN=1 command though, presumably because...
Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi all,
I installed Nordic examples for Keil MDK, and I am able to compile the examples for the PCA10028 board, which is based on the nRF51422. But I intend to take the...
Hi, I am using 1 central and 2 peripherals. I tried erasing bonding info in both central and peripherals for a few times (by calling pm_peers_delete() in the central and pm_peers_delete...
Hi,
I am using NRF51822 and GCC compiler. I am using softdevice S130. SDK 12.2.
I want to receive the data from Peripheral that is one way only.
I want to use multilink...
Hi everyone, I have one question shown in the title. I try to add a second service in "ble_app_uart" project (the project is in the SDK for nRF51, SD130 v2), I did not change...
Hello,
I was using the nrf24LE1 where i used hal_nrf_set_power_mode() to set the radios' power down mode. Options are power-up and power-down. This is when i was using...
I have a system, with cc2540 as central and n51822 as peripheral with s130. Sometimes while they are close to each other, the connection link gets lost.
I disabled updating...
I'm using SDK14, S132 5.0 and nRF52832, and trying to enable and disable softdevice in my application. In main function, the power management loop is like
while(1)
{...
I am using SEGGER Embedded Studio for developing mesh network on nRF52832. For curiosity I pressed the BOOT/RESET button (SW5) while applying power to the board and it entered...
I want change project "record_launch_app" purposely launch my own app use the NFC tag on an Android device? Where should I take "m_android_package_name" of my app?
I used...
Hi,
I have a basic characteristic on which I would like to write. I did this on so many projects without any problem but here, the value handle of my characteristic doesn...
Hi,
I'm currently testing the pc-ble-driver.
It seems its only supporting exactly one FW version and I wonder why.
As far as I understand it currently supports v2 (S130...
Hi,
I'm using nrfjprog with nRF52, SDK13 & S132 soft device.
I do not use mergehex during my development cycle: I flashed S132 hex once, and only reflash my application...
I programmed to nRF51 DK, the first time the device is connected to mobile phone.It works, but if i turn off the nRF51 DK and then turn it on.it is connected but it cound...
