Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
I am trying to build a basic communication system without GATT or GAP services.
I don't have any device that is advertising, but it seems that my device get a
BLE_GAP_EVT_ADV_REPORT...
Hi,
I'm using nrf51822 and ble_app_uart(SDK 12.3.0).
I'm sending data from my android phone.
My question is that what happen if send data before previous data is...
Hi!
I am developing application for thread on NRF52840. I've got one problem with connection stability. Sometimes some SED nodes are disappearing. Only reset makes them to...
I am using CC2541 and CC2540 (USB dongle) which will communicate with each other and transfers data. I want to know weather i can communicate to CC2541 (ble device) directly...
Hello,
We have a setup where we connect an nrf51822 and an iphone.The nrf51822 connects to the iphone,
notifies the data and disconnects roughly every minute.(This is done...
There are only HID periphral sample code in nRF52840 SDK.
It is difficult for me to implement HID central with the sample and tutorial provided.
So I want to get a sample...
Capture_Load_error.PNG
All,
I'm new to the nodic. Just now installed KEIL V5.24.2.0.'m able to compile code but not able to load it on Target.
Please find attachment...
Hello,
It doesn't seem possible to mimic a IEEE public BLE MAC address using the BLE stack provided by Noridc. But how easy is it for others to roll their own BLE stack that...
For longer than I'd like to admit, I've been trying to make an application on the NRF52832 that relays UART data to a phone. To date, I've:
Gotten the BLE_APP_UART application...
hello all：
I think sdk13.1 s132 has a bug about ANCS，
ANCS works normally only in the following two cases
1、Both the phone side and the device side do not remember...
I have a sensor with serial protocol of 7 bits data, even parity, 2 stop bits. I wanted to use uart library to interface with this sensor. But I couldn't find the settings...
Some times when I'm trying to use GDB it stop with the following information:
(gdb) file _build/nrf51822_xxab.out
A program is being debugged already.
Are you sure you...
I started to try SAADC example in SDK12.3. After setting up project in eclipse, I got two errors:
Symbol "NRF_TIMER0" could not be resolved
Symbol "TIMER0_CC_NUM" could...
Hi,
We are a group of students at NTNU looking at the possibility of creating a small device that connects to your phone and multiple other BT devices simultaneously, letting...
Hello,
This is a quick question regarding the behavior of the Power Supervisor POF warning. We implemented a fairly naive use of the POF warning where we would log an POF...
