Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi,
I am currently going through the GCC and Eclipse tutorial. Now I struggle to compile the project.
I installed the blinky project (nRF5_SDK_11.0.0_blinky_blank_pca10040...
Hi all,
nRF52840 and S140 support bluetooth 5. Bluetooth 5 expands 8.x adv data length. I test it on the ble_app_att_mtu_throughout example and add more 30 bytes data to...
Hi,
I have a question about choosing "correct" soft device. I need only peripheral connection, but I'm bit in doubt for choosing SD110, because compatible sdk ver 10.0...
what is the function of bsp.h header file. if i use my custom product should i also use this header file?
i am tring to make LED blink with custom port pin. (different pin...
HI, i'm trying to perform the following operations with the Core Bluetooth Framework of iOS:
Connection to peripheral
Services Discovery
Characteristics...
Hi
for some reason I cannot connect any PC terminal to my custom board: I would get consistent NRF_UART0->ERRORSRC = 0x000c or 0x0004 indicating break and/or framing issue...
s132 4.0.2, nRF5 SDK 13. In BLE_GAP_EVT_CONNECTED event handler I try to call sd_ble_gap_data_length_update returns NRF_ERROR_RESOURCES.
I have
#define NRF_BLE_GATT_MAX_MTU_SIZE...
Hi all,
I have some question want to ask.I have about 200 bytes to write to the flash and also I would use the bootloader.
I'm using nRF5_SDK_11.0.0_89a8197 and s130_nrf51_2...
This test program is modified from examples\pin_change_int\main.c, I add the instructions to put the cpu to sleep. And I add nrf_gpio_input_disconnect() for all the pins except...
Hello, I am using pstorage function and I would like to know oppionions of your's what would be the best practise to wait until processor erases the flash memory and would...
Is enable required before configuration? Does toggling NRF_ADC->ENABLE reset the configuration (like it does for the radio?) Is the power to the ADC automatic, so that even...
im using sdk10, I initialiszed ble_stack_init and advertising_init but when starting advertising, it works with BLE_ADV_MODE_FAST but not with BLE_ADV_MODE_SLOW .
why it...
Hallo comunnity
I have a sensor which is working is sending data via BLE and it has a 128 UUID bit service [0x 000000-000000-1000-8000-0080-5F9B34FB]
In order to do...
