Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi,
What is available MTU of CoAP and UDP over 6lowpan with IoT SDK ?
In my application, I need to transfer dozens of kb data to ble node over 6lowpan with iot SDK. Do...
Hi, I bonded is ok .But I want to store some data on nrf51822 flash memory using pstorage. What should I do?
Register new or change it :
param.block_size = ALL_CONTEXT_SIZE;...
I have an SPI peripheral that has an odd protocol and in trying to sort out why it was acting up I finally caught a logic trace showing about a 13us break in the SPI data...
Hello,
I am using HID mouse/keyboard examples from SDK to learn creating custom HID device.
Besides using four buttons on EVK to simulate motion action. I would love...
Hi All,
I'm currently setting up three nRF52840 DK nodes, two nodes are routers and one is an end-device. My plan is to introduce more node in the network later on. The...
Hi,
We created a faster & simpler alternative to gazell for the nRF24LE1 (our IoT sensor) that supports 100s of transmitters (PTXes), is individually addressable, has session...
Hi
I'm using the NRF51422 with hardware UART.
Brief outline of the configuration:
115200 Baud, 8-N-1, no HW flowcontrol
SoftDevice S130 V2.0.1
lib: app uart fifo
...
Hi all,
I am using the softdevice S130 v2.0.1, plus one application derived by the ble_app_uart and the single bank bootloader (SDK11) on a custom board with the nRF51822...
Hello community
I'm trying to do a central app, for this im using the example of UART_Central with the SDK 13 and SD S132.
During the events cycle I am having only the...
Hi,
when executing the following code in my application. if face chip reset time to time. I've investigated code to find the bug origin and then notice that i ve a difference...
i am using Nrf52840 with SDK 132 and version 13.
here is the initialization
ble_radio_notification_init(APP_IRQ_PRIORITY_LOW, NRF_RADIO_NOTIFICATION_DISTANCE_5500US...
I am using ble_app_hids_keyboard example from SDK : nRF5_SDK_12.2.0_f012efa with nRF52 Dev kit. In that example, keys_send() Function is calling under BSP_EVENT_KEY_0. which...
Hi Sir,
I want to run the spi master example code with my nrf52832 board. In sdk11.0, have mentioned for pca 10036, the CS pin should be 29. If that was the condition,...
