Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
I have two sensor: Si7021 and CCS811 connect to board (nRF51 DK).
Si7021 work fine.
CCS811 always return NRF_DRV_TWI_EVT_ADDRESS_NACK error.
Anyone can give me a help?
Hi,
I'm trying to setup NRF52 with a microphone (ICS-43432) using I2S and easyDMA. I'm new to embedded software development, and would very much appreciate your help and...
Hi,
I am really new to the Nordic products and programming for that matters. But, the thing is that I am in somewhat of a hurry. I would like to use a similar code to below...
Hi all. I am sending to BLE device AE A7 04 00 05 09 BC B7 command, getting status 0 ( success ), but do not get any updates or notifications from BLE at all. So am I doing...
I've compiled the secured DFU bootloader (from SDK 12.2) and loaded it on my board. But whenever I run my firmware, it won't start (none of the expected interaction happens...
Hi there,
As the title says, i'm tring to add nus service to the freertos example (board PCA10040, SD 132, SDK 12). Actually, I want to mix it with the peripherical app_uart...
We started with normal Pstorage functions and add now some pstorage RAW functions.
Could anybody explain the resulting and needed linker script definitions flash allocation...
Hi!
This is my first time working with bluetooth and Nordic chip and I'm having program getting started.
I'm trying to program the Sparkfun nRF52832 Breakout Board as...
1.application downloading
we need to download the appliacation to the address which is designated. However, the NRFgo Studio offered offically can't designate the address...
Hello,
I'm new in programming beacons and ble sofware. I'm using the nRF51822 Beacon with S110 and the USB Dongle.
I updated the beacon with the example ble_app_beacon via...
hello, i am new to the Nordic controllers.I am having 2 doubts.
i want to modified saadc example code in keil 5 for that i want to add "app_timer.h" header file...
Hi guys.
I want to make use of CLI in my existing project based on ble_app_uart .
I was looking at the diferences of there sdk_config.h and there is a lot of stuff happening...
sd_flash_write(((uint32_t *)storage_addr),
(uint32_t *)p_data_addr,
size / sizeof(uint32_t));
why here size value is divided by sizeof(uint32_t).
what is byte value...
Hi,
I'm trying to adapt the HRS/RSCS relay example from the SDK to use the Nordic UART service instead. Currently I can connect to the central just fine, but if I try to...
I'm using RTX timers on NRF51 and I'm getting a 7ms per second error. (I.e. osDelay(1000) takes 1007ms).
It appears that NRF_RTC1 is configured incorrectly in SDK examples...
