Hi All, In the NRF54L15 SoC, the main ARM core and the co-processor RISC core share the same set of peripherals even though both the cores can have separate sections of RAM...
Dear Team,
We are currently using the nRF52833 as the BLE advertiser (cattle node) and the nRF5340 as the BLE scanner/gateway. The system is based on BLE Extended Advertising...
Hi,
1.Can the sQSPI and SPI functions of nRF54L15 operate simultaneously at 32 MHz on the P2 port? 2.Can the sEMMC and SPI of nRF54L15 operate simultaneously at 32 MHz on...
Hi
Currently I'm evaluating the nRF54L15 die temperature sensor. I’ve taken a few measurements and noticed something I don’t quite understand yet. Perhaps someone could...
Hi
We used ALA321C3 like antenna for the chip nRF54L15 , but we have a little probleme that the signal of it is not stable.
So we need your teams to help us.
And we...
I have around 140 BLE Scans per second in my environment. I can see them with a NRF52840 with SDK 17 and with an ESP32 as well.
But when I scan using NCS 3.2.2 I only get...
Hi,
I am using two nRF52833 devices with the nRF5 SDK. They are paired and bonded to each other. Occasionally, I encounter the following error in peer_manager_handler :...
At s120,i used the following code to send data (to s110)
if( ( wIndicationFlag_Get() == true ) && ( wConfirmFlag_Get() == true ) )
{
//APPL_LOG("Write Data\r\n");
...
Hi Nordic,
From the topic: APP_TIMER_TICKS value , I've know how to use it, but is it possible to use different prescaler value in the same code?
For example the nRF5_SDK_12...
Hi, I need help for generating the init packet. I'm using SDK 11.0.0 , s130 on nrf51822. To build bootloader, I've used the sample bootloader with some include path changes...
I try to print the RSSI level but i couldn't do.
I use nRF51 DK and soft device S130.
This is the line that i just write:
SEGGER_RTT_printf("RSSI: %d\n",p_gap_evt-...
I'm trying to create a project from scratch that can use the S132 Softdevice, but I am constantly running into problems trying to get the correct headers, preprocessor macros...
Hello Nordic,
I am using the BL600 third-party module and SDK 10.
I was able to modify and compile project with GCC at
examples\ble_peripheral\ble_app_uart\ for s110...
As title,
I found that on the official website,
and I think it's extremely useful for someone(me) who need to measure the power consumption(current).
I can't find...
When I operate RESET PIN in main function like this:NRF_POWER->RESET = 1,Then cause a HardFault_Handler, (/attachment/fabd1141d36157d32f8c0353e4880b3e),What's this？
hi NORDIC,
is it possible to store float array in fds. i am able to store intrger values but unable to store float values. i am using example in this link :- github.com...
We have observed in couple of large size deployments that data packets from beacons that are bit far away tend to be corrupted. Devices that scan the signals from BLE beacons...
I have read the previous questions regarding the above subject, i found that changing the maximum bonding devices limit defined in device_manager_cnfg.h will work, but it...
Hello everyone, I must to write and read a I2C eeprom like 24c256. I tryed to do it but all the examples with I2C protocol works with 8bit addressing. I tryed to modify mpu6050...
Does the components on the development kit increase the power consumption compared to what you would expect from a low power-optimized application-specific PCB?
Other than...
I use the ble uart app to receive the data from mobile phone. The data packet size is 20 byte. If I transmit the packet one by one without adding delay, is it possible that...
