RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Hello,
I need to get RSSI with the NRF51422 (pca10031, S110), but i don't want to connect with a central device (i.e. Smart Phone). The central device should scan for bluetooth...
We tried to pair with and connect to nRF51822 DK running HTM app with SONY VAIO fit15e NB and always fail as we did the following steps.
We also tried some devices like ASUS...
Hi,
I just replaced the BLE chip in my board from CC2540 to nRF51822. I simply want to know how to configure the interrupt on a pin as well as rising/falling edge interrupts...
What are the allowed channel numbers for gazell?
In the gazell user manual it states, a possible 80 channels.
While the nrf_gzll_set_channel_table () API reference says...
Hi,
Is it possible for me to completely copy the antenna design from PCA10028 unto my custom board? I don't need a very long range, but I need to make a design fairly quickly...
For PCA10001 have 16MHz crystal, and I use the NOP to test the cycle. And found the device work in 16MHz. How to set this board as 32MHz?
This is my current setting in...
We need to sample all 8 ADC channels for random 1ms pulses to record amplitude data from in real time. How much will that impact the bluetooth performance if it needs to freeze...
Dear community,
I would like to know how to send as much data as possilbe from a Nexus 4 to an NRF51822 based device. For that I think I need to send multiple packets per...
Based on the announcement for upcoming training ( www.nordicsemi.com/.../Bluetooth-Innovation-Trainings) it sounds like Nordic will support the Bluetooth SIG's Bluetooth Developer...
Hi, Is there a UART bootloader built in to the factory firmaware similar to others like NXP LPC series where a specific pin is held low at reset. If so what pins are used...
Hi, Nordic Engineers:
Pls give your hand, new question: Could i run two app on one mobile-phone that connceted with only one device? also, they can operate the device by...
Guys, I would like to put the internal uC in sleeping mode while nRF51822 is advertising and wakeup him, when I establish a connection.
I know that is possible, it must...
Alright, so I am having a lot of trouble generating a valid zip file to update with nRF Toolbox (android).
I used nRFgo Studio to flash dfu_test_app_hrm.hex and dfu_test_bootloader_b...
