Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have seen this forum post: devzone.nordicsemi.com/.../
Which refers to this blog post: devzone.nordicsemi.com/.../
But when I use the Keil Packs Installer, and check...
Hi,
I'm approaching the nRF51 tools for the first time and I'm trying to recompile the source code for the desktop 2 reference kit with Keil 5.14 as a sanity check for...
I am developing an application where a repeater unit connects to a number of other units, gets some info, aggregates it and broadcasts it as a peripheral unit (in a tree structure...
20150424_iPad_iOS(8.1.3)NrdkKS_sniffer.psd
Dear Nordic,
I want to control the volume up feature through HID for iOS while pressing the key.
How can I proceed for...
Greetings,
I have a peripheral (S110) , when it is connecting to a central, it also need to scan another broadcaster (beacon) to obtain its RSSI and send to the central...
I have adopted the S120/S110 multilink example to the following: central.zip and peripheral main.c
I want to send a notification from the central to the peripheral and...
I've developed an application on the nRF51 DK, now for further testing purposes I need to upload it to the nRF Beacon (PCA20006).
My software uses SDK8 (S11 v8) and it...
I want to get rid of the board support package, and write my own code to interface with the least complicated drivers for UART, BLE and SPI etc.
If I remove BSP I ifind...
hi i have pca 10001 eval kit .I need to connect it with PIC16L1947 controller via uart.The data transmitted from pic is to be collected by nrf51822 and it should send as advertisement...
I am developing an application from scratch for the pca10001 by copying a lot of code from the heart rate example.
When calling "softdevice_ble_evt_handler_set" I get an...
I am looking over the stack-up for the dev board which I received from an FAE and has designed in a 50mil width PCB antenna. I am using this online calculator here:
emclab...
Hello--
The nRF51-Dongle has these 20 pads which I think correspond to a debug port:
On the schematic, it looks like these feed into JTAG signals:
My question...
Hello,
I just got a nRF51 DK and I'm trying the examples of nRF folder in the Pack distribution (SDK 7.2).
I can compile the Blinky project but its not working if I...
i have the nRF51DK that comes with the Segger j-link programmer. Can i use the programmer on the board to program a custom board i purchased from Nordic preferred vendor?...
