Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
Using and GCC with compilation options without optimization -O0 and with debug -g3 throw error during compiling for an unknown function pwm_calculate_timer_frequency .
...
Hi,
I can't seem to get printf working on the ble_app_cts_c example. I can't seem to find a definitive step-by-step guide as to how to get this working. Any help would...
Hi,
On what occations do the BLE_GAP_TIMEOUT_SRC_ADVERTISING and BLE_GAP_TIMEOUT_SRC_SCAN events fire? The documentation is a tad ... terse .
regards,
Elm
Hy world,
I can update my device with FOTA, but the first time i do:
1 I put: "ble_default_bootloader.hex" on board;
2 i open nrfMasterControlPanel app
3 i write characteristic...
I have a feeling I am missing something completely obvious here. That said, this problem has cost me enough time today that I'm willing to risk embarrassment to see if someone...
I'm trying to implement a simultaneous broadcaster observer by calling ble_gap_adv_start() and sd_ble_gap_scan_start() and waiting for respective events.
If I call advertising...
Hello,
I'm trying to use Eclipse with a Nordic SDK (managed build mode) but it seems Eclipse (latest Mars edition) fails to invoke the assembler. Here is what I found in...
We are looking to use the DCDC to reduce the maximum current during radio operations, but minimize the overall current by enabling it as late as possible before radio use...
I have added button in my project and used bsp_init() to initialize it. All functions in bsp_init() returns NRF_SUCCESS but if I push my button even gpiote_event_handler(...
Hi Folks,
i have implementet a sleep mode by using only the RTC timer with the 32KHz OSC and the WFI instruction. The current consumtion is around 1.7µA (all peripherals...
Hello,
We have some problems with nRFgo Studio on the one of our computers.
Firstly, it takes a long time to flash firmware - about 15-20 seconds:
Secondly, we...
I have interfaced a vibration switch with nRF51822 Pin 19 using external pull-up. When there is no vibration the switch is either at open position or close position randomly...
UPDATED WITH IMPLEMENTATION
Is there a way to know what is triggering a chip boot :
Power off (battery replacement or deffective electrical connection)
The watch...
I have an old project I am trying to recompile for nrf51822 but have been programming with the most recent MDK on my station. The project is asking for old Device Family pack...
