Hi,
I want to add scheduler server to the mesh/light sample with nrf52DK, I change the element define like below:
static struct bt_mesh_elem elements [] = {
BT_MESH_ELEM...
Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
I just got nRF52 DEVELOPMENT KIT and NRF51822 BEACON KIT.
Can you tell me that where I can find the reference design for them and what could be the good starting point...
Hello, I am trying to program an BMD-300 using the NRF52-DK on a custom board,
The BMD300 is powered by the NRF52DK
BMD300 -> NRF52DK
SWDIO -> SH_SWDIO (pin 4) on...
Hi,
I just read IoT-MQTT example and have almost exactly the same problem but with the Publisher.
I am running a PI with Raspberian 4.4.34-v7+. I have installed mosquitto...
I am running the SDK12.2.0 ble_app_template peripheral example with RTT Logging enabled. The example seems to be running OK, but it logs: APP_ERROR:ERROR:Fatal with the ID...
Hi,
I am using NRF51822 to complete an application of multilink on one central . I tried to modify the central_link_count definition to 9 instead of 8, then I stuck on the...
Hello,
I am new on nRF51 and i would like to have a function to read the rotary position of motor in any rotary direction by adding a codewheel and a two channel reflective...
Hello,
I am trying to implement wake on motion functionality of MPU9250 with nRF52.
I am writing below sequence code for wake on motion configuration:
void MPU6500_StartMotionDetection...
Hi DevZone
I want to make a little beacon app, that advertises on channel 37 then waits 700 ms, advertises on channel 38, waits 700 and advertises on channel 39.
The below...
HI,
I wan't to read sensor data from ADC. So i use nrf_drv_saadc_sample() .
On Arduinos i usually call value = analogRead() and after that i process the data. But here the...
Hello,
We need to add custom data to advertise packet. As I understand we can use Manufacturer Specific Data. But to do this we need to get our Manufacturer ID from Bluetooth...
I have the following code for a custom service UUID and a custom 128 bit characteristic ID. I get a error of no memory available in our_char_init while adding the 128 bit...
Hi,
We bought a mac bd addr pool from IEEE
Where is the best way to store this mac adress during production ?
We guess the type will be: BLE_GAP_ADDR_TYPE_PUBLIC
Do...
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi. I'm using nRF51822, SDK12.2.0, S130.
I finally compiled bootloader_secure which was very hard.
Q1. After run bootloader, I can find the device using DFU "DfuTarg"...
