HI,
I am using the nrf_desktop sample in NCS V3.0.2, I want to buil with prj_release_dongle.conf , the setting
but build fail, I check the file Path: it should be F...
Hi:
PLEASE CANCEL THIS TICKET
I'm doing exercise 1 of lesson 1 of the nRF Connect SDK Intermediate course. It says: Get the source code of this course as a third-party...
I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
I'm trying to make a simple BLE app based on LED button demo (BLE_LBS.C) that probably don't use much resources. I added FIFO UART communication routines and when I tried...
I have an NRF 8001 BLE chip, can you provide the break out board schematic to make this chip discoverable to my iPhone 5 as soon as i power that break out board. And how to...
Can anyone tell me how to connect NRF 8001 with Arduino mega 2560. I have developed an iPhone application and just want to connect with NRF 8001.Please tell me how to connect...
OK, probably a dumb question:
The nRF51822 reference manual indicates that the RTC is driven by an external 32 KHz input. Can anyone confirm whether it will or will not?...
Hi
can you please help me convert these Keil pre processor calls to something that gcc compiler can . If possible i would like more information about these calls and the...
I'm using Nordic NRF51822 and the Segger JLink with the s110 Bluetooth stack active (correction: flashed on the chip, see below). When my code hard faults (say due to a dereferencing...
hi, I currently stuck in the follow section:
static void gpiote_event_handler(uint32_t pins_low_to_high, uint32_t pins_high_to_low)
{
if (pins_high_to_low & (1 << BUTTON_0...
Anyone to tell me where can i get the CDB file for nRF24LE01? I've downloaded the SDK and the nRF go Studio, but i still cannot find the CDB file.. Please help me to find...
Hello,
I'm trying to start softdevice on a custom board with nRF51822 chip and S110 device. The code hangs in SOFTDEVICE_HANDLER_INIT. It seems that EVENTS_LFCLKSTARTED...
Hello,
firstly I would like to say that I tried searching the forum for a post that has similar problems to my own. But I haven't (please tell me if i'm wrong) seen any...
Question: Can a nrf51822 acting as a server/slave message a client/master (iPad), that it has bonded with previously, to let it know that new data is available without having...
Hello,
I would like to experiment s120 on the evaluation board.
There are some examples but in nrf51/nrf51822/Board/nrf6310/s120/experimental.
Can I use it ? Or is there...
What are the correct PTX and PRX configuration settings for using dynamic payloads with auto ACK disabled? Can I just clear EN_AA and set EN_DPL and DYNPD for the pipe I'm...
Hello! I am working on a project in which I want to send stored sensor data to a smartphone whenever the phone is in range or at specific times of day.
Most of the communication...
